New profile posts

What's new New posts New media New media comments New profile posts Latest activity
A
I have a B2630 I purchased new in 2011 the receiver end of the seat belt quit holding the ratchet in place I can hear it snap in place but a nice tug and it pops right out.
I am looking fo a replacement receiver end.
Mountainman
Mountainman
Thank you for the inquiry but unfortunately i wouldn't have any b2630 parts or anything that new.
C
Find a snow blower for your B7800?
B
b12
Yes. I have a Frontier SB1164 rear mount snowblower.
Andy c
Kubota u173a. 2012
All works ok apart from arm and tracks which I assumed was a faulty safety switch, I have checked this and all is ok, If I give it full revs I get minimal track movement and arm movement, I have removed the hydraulic pump and spline etc all intact so could it be the solenoid off the safety switch? If so where would that be located? I would very much appreciate any advice
Regards
T
I have an L245Dt and I am looking for the left side axle. My manual has a part number of 35110-2711. Does anyone out there have a used one for sale?
Thank you!
T
Tcmk
007kubotaguy has the parts you need .
Andy c
Kubota u173a. 2012
All works ok apart from arm and tracks which I assumed was a faulty safety switch, I have checked this and all is ok, If I give it full revs I get minimal track movement and arm movement, I have removed the hydraulic pump and spline etc all intact so could it be the solenoid off the safety switch? If so where would that be located? I would very much appreciate any advice
Regards
H
I have a Kubota B2400 it is loosing power especialy in high gear I have changed fuel filter, fuel pump both new injectors, checked the timing gears, but does not have enough power when driving, will stall out without a strain, could it be hydraulics, i have the kubota servic manuals but can not figur it out, any help would be appreciated thanks
D
Daniel Pullum
I had a B2400. It had 85 hrs when I bought it from the dealer.
At 600 hrs the hydro peddle went nuts. The tractor would run/move until I dropped the scraper and the peddle hammered like a machine gun.
The dealer checked out, with no solution and called Kubota Central Service Center. A rep went to the dealer and made them repeat all the tests (mostly hyd pressures)they had performed. The service rep told them to give me full value on whatever I wanted. He took the machine back to headquarters. Quite a time elapsed before we got an answer. Wait for it on the next line.
THE WEAR PLATE BETWEEN THE PISTONS IN THE HYD PUMP WAS MISSING. THAT MEANT THE PISTONS WERE BEING PULLED .461 TOO FAR IN THEIR BORES. Probably built on Friday or Monday by a subsittute assembler.
TerryKing
Hi Fried, Thanks for various helps online.

Saw you have Fords and an 8N. Here's a photo I took 4 years ago as my friend Buck Spooner down the road finished a restoration for a customer:


Regards, Terry
  • Like
Reactions: 1 users
S
hello to anyone who might own a G6200 kubota with a 3 cylinder
it stop running and cannot move it other than lifting the rear end off the ground
does anyone know if that 1989 has a nutural gear to be pushed
sure help if i can find that out
thank you all that reading this
F
Firefight100
There is no neutral. You will have to lift the rear to move it or put it on a trailer.
  • Like
Reactions: 1 user
B
Have a b5200 need to replace glow plugs and glow plug incator new key swith belive key turns to left to make glow plugs to work
TerryKing
Hi EVEL (A Bike Guy, right??) You said " Oh, BTW, me thinks that was Sean Diddy Combs you quoted 😄 "
Jeezum Crow (A Vermontism) you must be a LOT younger than me, quoting guys that are still in Jail...
Regards, Terry
The Evil Twin
The Evil Twin
I don't know about "a lot" younger. Lol. I had just read a paragraph about the world of hurt Diddy is and all the bottles they found in his house. The quote could have been from him too.
Cheers!
-Dean
O
Greetings all,
New member, new 2380 with LP Grapple....3 hrs in, the jaws stopped opening/closing, everything else fine. looked and saw 4 wires sticking out below the joystick button....they must have been jerked out, tho not real sure how it happened.

I can see where 2 of the wire go in a quik connect, but cannot see where the other 2 wires were connected....need a diagram, manual not present, cannot find diagram online...anybody seen this or that wiring diagram for grapple?


i'm offically bleeding orange now!

cheers!
Dave_eng
Alan
To send you a manual I need your email address
What model is your machine as I only have a limited number of models
My offer to you is this as it has been to all others looking for WSM's.
Send me your email address

I will sent to your email address a Jumpshare link to download the WSM.
Once you have it downloaded, if you agree it is as stated, you will agree to upgrade your forum membership to any of the paying ones.
These funds help keep the forum up for everyone's benefit. Nothing comes to me!!!
If you do not see the link in your email IN box check your JUNK folder.
If you are having tough times financially, tell me and I will make an exception

Dave
M
I just got a 2005 Kubota BX1500, 1 day ago. It ran great. I love the tractor. Today it will not start, no power or lights, everything is dead. The battery and fuses are okay. Does anyone know what the problem is? Thanks
B
We are looking for the bucket tilt lever for our L285 tractor. Ours is bent and cracked, I'm afraid if we try to straighten it it will break.
Top Bottom