New profile posts

I own a 2014 RTV X1100CW that has been stalling randomly. I can keep it running by pumping the accelerator. It’s obviously a fuel supply issue so I changed out the fuel pump and fuel cut out switch. This didn’t solve the problem so my next move was to pinch off the 1/8” over flow line that runs from the fuel filter housing to the top of the fuel tank. It has solved the stalling problem for now. Does anyone know if there is a check valve in the fuel filter housing that may of failed? Next move is to replace the Filter housing?
TECH101
TECH101
Yes there is a check valve
I have a 2018 Kubota 2650 with 300 hours.My tilt wheel want stay in the down position and I have to pull up the foot release to get it to lock into any position.Seems something is bent or something.Any suggestions before it goes to shop.
TECH101
TECH101
Check your cab mounts I have seen it do some funny things
I need some good advise and small tractors but still able to dig rocks, plant tree's and run a how with force. I have a M5400 and need a turf tire with a bucket & hoe either the L series used or a Bx. I just feel they look to small but I AM SURE YOU OUT HERE KNOW BETTER! My 5400 is a1990 large frame . Beast from owning but great a brush cutting!
Question about a 7040
I have a 7040 with one remote my question is it suppose to spring back to center when released or do you have to move it back also when moving it foward it is hard to push and pull it out haven't had the tractor long still learning things about it any help would be great thanks
B7510 won't start!!
this happen a month ago, turned out to be a blown fuse. this time the tractor started to stall at times when forward or reverse peddle was pressed, if the peddle was released it would stay running, then it completely died. I can turn starter over by bypassing the OPC controller modular won't turn actually start, is there a way to test the controller to see if it is functioning properly? or if some one has successfully by passed it to get tractor to fully run?
Did you ever resolve your M135GX hydraulic problem?
I have the same issue. Everything works but the remotes.
I have an electrical problem on an L 2500 DT. Batteries, good power to the ignition switch but no lights on instrument cluster won’t do anything when you turn the key completely dead.
A nurse by day and an amateur Farmer/Small holder by day also. Staunch Remainer 🇪🇺 I have 2 Tractors but only one works
not sure if i am sending this message correctly? i was inquiring about a quick attachment for my kubota tractor that you had listed a few years ago?
I have a old school kabota B7100 HST. My lift arms raise and lower as they should but they slowly drop while in the up position. Any ideas as to what would cause this?
Good afternoon Lance, this may be the first in a long run of inquiries but looking for the lower grill for a L185…easy to fabricate something that would work but it would be great to find an original in any repairable condition…thanks for the assistance!
I have completed another maintenance task thanks to Tractor Mike, hydraulic fluid and filters changed. Not cheap, but finished. Looking at a 3rd function kit for front end loader. Any suggestions, not sure Kubota offers such a kit for my M5400DT
Hi All
I just purchased a used Kubota U27-4 Mini Excavator and looking for a custom cover to cover the controls, seat and possible the whole canopy to protect from the crazy weather ... Thanks in advance-
my BX 2370, I have discovered an O ring failure on the Forward hydraulic control valve assembly (just under the Battery) There is about 1 inch of clearance between the battery platform and the top of the control box. Has anyone any experience with with replacing the o ring part number 04816-00160? comments and suggestions would be appreciated.
R
Riceman
I started to take the assembly apart, 1st removed battery then found a cut out to allow bolt removal. problem solved.
Regarding the Mitsubishi tractors - Valley Power in Roanoke, VA used to be a good source of parts. Bill died and his store of parts has been auctioned or sold off based on another post on this site. I can tell you from experience the front spindles are prone to snap unexpectedly on the old Mitsubishi tractors. The loader adds weight the tractor was never intended to see. The first time mine broke a machinist friend was able to rebuild it. It snapped again within a month after selling the tractor. I never heard whether the new owner got it fixed. If you check the front axle capacity on many newer tractors you'll find the weight of the empty loader puts it near its limit. I found used tractors in my locale to be scarce and was concerned about parts availability. That's why I bought a new Kubota about four years ago. I wish you well with whatever you do.
  • Like
Reactions: 1 user
B3200 START PROBLEM. I'm sure it is the safety switch for the mid-PTO because I have had to "bang it" (the lever) a few times to get started. I know where the switch is, I don't know how to get to it. I don't think I'll need it as I'll never use the mid-PTO. Right now I have to hot wire the starter solenoid. Can anyone give me a guide to get to it?
Dear Sir: Thank you again for your very helpful reply. Thanks to your suggestion I found inline with the starter a 30 amp fuse. I measured it both ways with a meter and shows to be open. Probably my problem (I'm hoping). Now to find the fuse part number and get one. If it were not for your post, I may not have ever found it. Thank you again, Regards.
Hello Ping,

I see you made a home brew diverter for you bx2370. Would you mind sharing whats poarts you bought and sources.? Maybe cost. I am looking to use for a grapple.

Thanks
P
Ping
Surplus Center Diverter
13 GPM 12 Volt DC SAE 8 Solenoid Operated Double Selector Valve Dynamic DSV-62-08-12
. Switch from McMaster Carr wet location pendant switch mounted in custom loader handle. I'll try to get you a few pictures. I figure I have less than $250 in the whole setup. Not true 3rd function but, it works for me.