Quick hitch options

[DiggerDug2023]

Also,
Being somewhat new to using implements with my tractor(s), I have recently purchased a quich attach QH05 and want to use it with a LandPride RCR1242 with my BX1880 mostly for clearing small hedge type brush on my yard. Do I need a "floating top link" in addition to the quick hitch to use with this setup, and the same question if using my BX23S? Thank you to all in advance!

 

[Bee-Positive]

Page 20 of the RCR1242 manual shows a floating top link already on the unit. The QH would need to be adjusted so the top clevis pin is vertically over the lower pins to keep the deck level.

Center 3-Point Link Adjustment - Land Pride RCR1242 Operator's Manual [Page 24]

Land Pride RCR1242 Manual Online: Center 3-Point Link Adjustment. Figure 3-3 Center 3-Point Link Adjustment Refer to Figure 3-3: 1. Lower cutter deck to the nominal cutting height. NOTE: Customer may adjust center 3-point link to his or her preference. Lengthening center 3-point link...

www.manualslib.com

 

[DiggerDug2023]

Thank you for your reply, my friend! I am somewhat confused though, seeing that the QH05 model quick hitch has a "fixed" top connection that doesn't allow for the adjustment that it looks like called for in the diagram. Now, grant you, I have not tried to hook this up as of yet to the bush hog, but to another implement that is much older and just may not have been compatible at all. I noticed on the LP cutter the "quick attach" logo, and of course the quick hitch itself is for this specific implement. I just wanted to confirm with a very knowledgable group on the subject before that I proceeded to connect the two pieces of equipment to be safe. Again, I greatly do appreciate your sharing of the info!

 

[skeets]

Well Digger, welcome to a large Orange dysfunctional family Odds are if somebody in here cant come up with the answer, you dont have a problem

 

[Bee-Positive]

You may be just like me, I'm a visual learner and need lots of pictures. LOL!

The circle on all the pictures is where the top hook on the QH10 fits on the upper clevis pin of the RCR1242.
The arrows show the floating top link already on the RCR1242.

Put your QH10 on the tractor, back up to the RCR1242 and hooker up. The width of the QH must fit the lower pins on the mower. You may have to raise or lower the top hook on the QH to line up with the upper clevis on the mower.

Screw the top link adjustment on the tractor in or out to get the upper clevis pin to line up with the lower hitch pins. Follow the instructions in the link I gave to adjust the cutting height.

 

[Bee-Positive]

Sorry should have included this one also.
Arrow is pointing at the tractor's top top link you turn to adjust the Top of the QH in or out.
Follow the instructions in the manual.

 

[North Idaho Wolfman]

A QH 05 and QH 10 will not work for that Mower, you need a QH15 or better yet QH16.

Or save a ton and get one off ebay or harbor freight with a removable top hook.

And moving this thread as you do not have a grey market tractor.

 

[BBFarmer]

Thank you for your reply, my friend! I am somewhat confused though, seeing that the QH05 model quick hitch has a "fixed" top connection that doesn't allow for the adjustment that it looks like called for in the diagram. Now, grant you, I have not tried to hook this up as of yet to the bush hog, but to another implement that is much older and just may not have been compatible at all. I noticed on the LP cutter the "quick attach" logo, and of course the quick hitch itself is for this specific implement. I just wanted to confirm with a very knowledgable group on the subject before that I proceeded to connect the two pieces of equipment to be safe. Again, I greatly do appreciate your sharing of the info!

This is what I had to have for my quick hitch and fdr1672