Cab Build
- Thread starter jb62901
- Start date
Hi jb nice job. I am a firm believer in do it your self stuff. If I can build it I ain't buyin it.
joekimtkd
New member
Equipment
B7510DT, 4' Snow blower, 4' Loader, 6' Blade, 6' 3PH Finish mower, 6' box blade,
What kind of material have you used on Glass and walls~~???
Walls are look alike some kind of plastic but looks so rigid.
and how did you secured them on the frame?
Walls are look alike some kind of plastic but looks so rigid.
and how did you secured them on the frame?
Sides were made from truck tanneau covers, frame is made from aluminum angle. Windows, Duraplex Acrylic
Frame
http://i33.tinypic.com/15374aq.jpg
Frame
http://i33.tinypic.com/15374aq.jpg
joekimtkd
New member
Equipment
B7510DT, 4' Snow blower, 4' Loader, 6' Blade, 6' 3PH Finish mower, 6' box blade,
Thank you for the reply.
Yes I've seen that aluminum angle iron frame picture.
but what I meant to asking you was that angled aluminum frame goes to actual tractor's frame.
Where did you hook it up to secure the whole cab?
I'm almost done mine too. I'm going to paint tomorrow.
Once I'm done, I'll post it here too. but if I could learn from you something
better idea on the securing onto frame...
Thank you again.
Yes I've seen that aluminum angle iron frame picture.
but what I meant to asking you was that angled aluminum frame goes to actual tractor's frame.
Where did you hook it up to secure the whole cab?
I'm almost done mine too. I'm going to paint tomorrow.
Once I'm done, I'll post it here too. but if I could learn from you something
better idea on the securing onto frame...
Thank you again.
joekimtkd; This cab is mounted both to canopy that was in place before the cab build and floorboard and fenders. see pic
floor mount
http://i37.tinypic.com/1izt35.jpg
then angle over fenders for rear upright angle to canopy
http://i33.tinypic.com/29o3nkh.jpg
Hope this helps
floor mount
http://i37.tinypic.com/1izt35.jpg
then angle over fenders for rear upright angle to canopy
http://i33.tinypic.com/29o3nkh.jpg
Hope this helps
Joe also see the front and mid angle uprights to canopy, can't see the rear but it also came off the fender angle to the canopy.
Guess I should of taken more pic
http://i36.tinypic.com/2mdfous.jpg
Guess I should of taken more pic
http://i36.tinypic.com/2mdfous.jpg
joekimtkd
New member
Equipment
B7510DT, 4' Snow blower, 4' Loader, 6' Blade, 6' 3PH Finish mower, 6' box blade,
I should have seen your cab before I built mine~~~
Well~ some how, I did all the mounts on my idea which I had to squeez
my brain sooooo hard.:
Possibly next week sometime I could post mine though.
Tomorrow, I'm painting. and put all the windows, doors back on.
and final touch for the cabin. and Have to install all the lights for front and
back and inside light. and then have to build some tool box inside of cabin too.
and then I'm going to modify the snow blade to installs onto my bucket.
so I could use snow blade all times as well as bucket for snow removal.
Well~ some how, I did all the mounts on my idea which I had to squeez
my brain sooooo hard.:
Possibly next week sometime I could post mine though.
Tomorrow, I'm painting. and put all the windows, doors back on.
and final touch for the cabin. and Have to install all the lights for front and
back and inside light. and then have to build some tool box inside of cabin too.
and then I'm going to modify the snow blade to installs onto my bucket.
so I could use snow blade all times as well as bucket for snow removal.