Brush hogging with the BX23s

[jwolfet]

This tractor is around 2 weeks old or so now. I was told I wouldn't be able to clear land with it.... that was incorrect. Infact I did so with the 42" land pride rotary cutter... i won't say it was efficient but in alot of cases it was the right size to get inbetween stumps (which brings up another problem ... too many stumps to deal with - i'd be there for 9 years trying to dig them out with the back hoe - the smaller ones i could deal with, with the backhoe - the 2+ ft stumps looks like they will be challenging).

As far as danage

I have a ding my floor board the grill guard isn't sitting right - i kinda rammed a stubborn tree i was trying to push down (I did win - but it looks like it bent my brush guard a little). The day old brush hog has seen better days... no longer new (nothing a hammer won't fix). I did have my bxpanded skid plate on - and that thing is worth its weight in gold.

16 new photos · Sunday, Aug 23 📸

Tap to view!

photos.app.goo.gl

 

[NCL4701]

A large pipe wrench (and sometimes a cheater pipe to make the handle a couple feet longer) is pretty handy for pulling out damage on a bush hog caused by backing into stumps, rocks, largish trees, etc.

I’ve gotten pretty efficient at it after a good bit of practice.

 

[Shawn T. W]

It's not new anymore!

But, yes these little tractors can get a lot done!

Backing into stuff with the tail wheel high can get some stubborn stuff down, just let it chew it up, everything doesn't need to be cut down to only a few inches the first go round ... Second time around when you can see better will make a huge improvement!

ETA - If the stumps aren't where you plan to build a building or driveway, and if the stumps are less than 3"-4" tall, I'd just run over them, or chainsaw them down to that level, yes it will be "bumpy" if a tire goes over them, but the brush hog should clear them ...

I've read they make a chemical "stump remover" that you just drill some holes or cut slots in the top of the stumps, and over time they rot, much faster than naturally ... Then a root ripper could probably get the rest of it out ...

The stuff over about 1.25" you can chainsaw, or if not to much bigger a set of pruning loppers will get them out of the way!

 

[jwolfet]

A large pipe wrench (and sometimes a cheater pipe to make the handle a couple feet longer) is pretty handy for pulling out damage on a bush hog caused by backing into stumps, rocks, largish trees, etc.

I’ve gotten pretty efficient at it after a good bit of practice. View attachment 178492

I used that strategy as well.. Overall impressed with the BX and the little 42" cutter that the dealer recommended - there were a few times it bogged down/stalled - but i learned to lift it up quickly when it does. My biggest issue was getting to not tilt to the left - had to keep adjusting, that right side on the 3pt - and it would keep getting undone (even after setting the lock nut).

I am curious what a bigger tractor would have done - my biggest obstacle was maneuvering around the stumps and all the ruts i kept getting into. After all that it will need stump removal still and grading (alot of work). Contemplating to 1) Either get a bigger tractor 2) Skid steer (compact track loader) or 3) Mini excavator. This specific part was previously timbered - so lots of stumps every 10 ft or so... some pine stumps some of them are just monstrous.

 

[jwolfet]

It's not new anymore!

But, yes these little tractors can get a lot done!

Backing into stuff with the tail wheel high can get some stubborn stuff down, just let it chew it up, everything doesn't need to be cut down to only a few inches the first go round ... Second time around when you can see better will make a huge improvement!

ETA - If the stumps aren't where you plan to build a building or driveway, and if the stumps are less than 3"-4" tall, I'd just run over them, or chainsaw them down to that level, yes it will be "bumpy" if a tire goes over them, but the brush hog should clear them ...

I've read they make a chemical "stump remover" that you just drill some holes or cut slots in the top of the stumps, and over time they rot, much faster than naturally ... Then a root ripper could probably get the rest of it out ...

The stuff over about 1.25" you can chainsaw, or if not to much bigger a set of pruning loppers will get them out of the way!

thats where i kept having to be careful .. once i cut down a small tree - it's not down to the ground - thats what caught my floor board and caused that ding.