Search results

Anyone know what the rear center-disc measurements are on the 12.4-24 rear for a L295? My tractor is 45 minutes away? I know it is 6-lug. Found rims on FB that look like a possibility, but says came off Ford? Any chance these will work?

Thanks. I’m trying to find two rear rims 12.4-24 (quite a bit larger) but trying to get a reasonable “ballpark” of what shipping is across the country!

Here’s a pic the current turf tires and rim….but the front is the 7-16 with AG tires!? so I want need the correct “center disc” on 10x24 rim that will then fit the 12.4-24 tires I have on order. The heaviest (and most expensive with most expensive shipping) is the center discs. anyone have...

What method of shipping and how expensive?

Where are you located? I might be interested in front wheels? Are they rusted at valve stems?

I've been looking on FB Marketplace quite a bit. These specific rims for a handful of decades-old tractors are a bit harder to find. Then there's a limited response rate, no longer available, or 6+ hour drive.....so I'll keep looking there, but I was hoping someone on this forum may have, or be...

I need Rear Wheels (AG) for my L295DT. It is a 6-bolt, 24" rim. Specs call for a 12.4-24 AG Tire. I think rims from some other models will fit. Dont necessarily need the tires. I'm in North Carolina. I know there are some available at Salvage Yards, etc. across the country (or half way!)...

Thanks. Can you explain further? How is this supposed to work? How can I diagnose/fix? Is way I’m using it OK?

Sorry for the “first timer” question. My L295DT has 2 levers on right to control the 3-point. I have a bush hog attached. The inside one raises/lowers, but it kinda seems like it’s all -or-nothing.depending on how far you pull the lever, it just slowly/quickly keeps raising or lowering till it’s...

I was just reading thru some other threads about sealant on fittings. we used yellow Teflon tape on the NPT fittings. Many seem to say not to do that (use dope instead). Should I break those lines again and clean off the tape and use pipe dope?

Reviving an old post. I finally got to replacing some of the ancient hydraulic hoses on my L295DT with L1200 FEL - to be totally honest a friend did most of the work and I helped!! On 3 of the hoses that come off the controller and connect under the seat….. I’m not sure what the diameter of...

I’m sure I made a wrong assumption off previous research…or my understanding of what “Grey market” means, or perhaps just the difficulty I’ve had finding parts!!? it is a L295DT and I believe the loader is a 1200!? I have procured manuals/parts lists for both. everything is painted over. I...

I will try to look for it this afternoon. Any idea of where to find it on this old gray market, painted over tractor?

Re-posting my old question. Can anyone help with part numbers and/or source for L295 DT Tie Rod and both ends?

My tie rod ends are shot, and it looks like rod is bent anyways. I also wouldn’t know how to adjust new ends only. Is there an aftermarket assembly for my tractor with rod and ends I can just replace? I’m not finding part numbers from old manual or Google search.

I think only one…but I’ll check!

Ummm….probably been sitting for a month or so since I cleaned/replaced. I don’t see rust in tank? I’m thinking that even though I could see some fuel in the bottom of the tank, perhaps dry at valve since parked on an angle and got air in lines? I don’t see any fuel stains or in dirt? After I...

Several months ago - my L295DT sputtered out and wouldn’t restart while I was brush hogging. There was lots of gunk/sediment in tank and clogging fuel. a friend help me remove tank, clean (including valve). We reinstalled, new filter, line, bled, got it to start!! Today, I went to property...

Will do. Wish you had the suspension assembly- I’d rather buy from you than eBay!