Search results

Hello KJ ..........., Welcome! You can use the attached link for information on your tractor. As I mentioned in my initial post, you will need to contact the factory for more specific information. Perhaps a dealer could be of help, but I rather doubt it...

Try Kubotabooks.com You may get lucky and get one to download for free.

Welcome to the forum. The members have a wealth of knowledge, and are ready and willing to be helpful! I found this video to be informative. It is worth a viewing. Good luck with your purchase...

You didn't mention whether your tractor is 2WD or 4WD. If it is 4WD you will want to maintain the circumfrence ratio between fronts and rears as was the original. This is because you want the fronts covering slightly more ground than the rears to maintain steerage. "Pushing" the fronts is not...

You should be able to "pin" the deck up using part #70

This may be of interest. https://forums.ybw.com/threads/soltron-startron-xbee-explaination.84653/

Wolfman, My confusion stems from the FAQ section on the GTR Inc., San Pedro, CA website. They claim that the products are identical. Please see attached

Thank you for the reply. I am referring to Diesel use.

Thanks Geohorn, I did go to the site, and read everything. Seems to be a lot of "he said, they said, you said". So, I still don't have a simple answer.

Soltron has been mentioned as a preferred additive for warm weather use. It is hard to find in my area, but Startron is available. The manufacturer claims them to be of identical formulation, and are named differently for marketing purposes. I checked the MDS sheets, and they are not the same...

Is this a new noise? It kind of sounds like the noise my B2650 makes at low RPM, and my "rattle" has been attributed to gear lash. Straight cut gears will do that. Just a long shot, but at least worth mentioning. Bob

It looks like the lights you have shown us draw about 4 amps. I believe that the circuit you would use is rated for 10 amps, so you should be OK Goos luck with it. Bob

The part number for a complete top link with depend on whether it is a Cat 1 or Cat 2 Go here https://apps.kubotausa.com/illustrated-parts/ Agree to the terms of service, put in your model number and go to the three point hitch/drawbar section I have had good luck with eparts store...

Hello Billy G, Welcome to the forum. This is a long shot, but worth trying. Clean the air intake vents of the fuel tank cap. They can get clogged and then a vacuum is created in the tank and ................no air in, no fuel out. Yup, it is a long shot but it is so easy to check. Just take off...

All the parts for the B7800 are shown here: https://apps.kubotausa.com/illustrated-parts/ Good luck searching! Bob

In my post above I explained that I had bent the top link on my B2650, and used the e-parts replacement. As I mentioned, it was an exact match, down to the paint color. . I also talked about why you can't replace the threaded ends as a stand alone part. Bob

Hello Wolfman, You can go to e-parts shop directly and save $14.00. I attached the link in my post. Bob

I went through this on my tractor. My B2650 and your LX2610 use the same 6C200-65400 top link. In my case, the Phillips head screws cover an access point that is used to mar the threads. The threads have been flattened and the end fittings will not come out. I suppose that I could have put it in...

Hello DustyRusty, An alternate thought on running in 4WD. When 4WD is engaged, the front tires, by design, will cover slightly more ground than the rears. This is done to maintain steerage. The fronts are actually "pulling" the rears very slightly. Not a problem on a soft yielding surface. On...

After all the coolant (antifreeze) talk, I guess I will stand by what I said in a post some time ago. "1) Using distilled water for mixing is better than using well or city water. (You can do what you think is best for your machine) Distilled Bourbon is not good for your tractor, but it is...