Search results

Thanks for the input! Sent from my iPhone using Tapatalk

I looked but there was only one with a backhoe and it’s a very suspicious ad IMO. Sent from my iPhone using Tapatalk

Yes I forgot to include that it is an HST, thanks. I believe it’s a 2015. Features, I don’t know what you mean? Sent from my iPhone using Tapatalk

As the title says I’m selling my L3901 (with deep regret). It has almost 300 hours and comes with backhoe, 3rd function valve with Land Pride 1060 grapple, Land Pride back blade and an old brush hog. Also installed a block heater. It has been meticulously maintained and everything works...

Thank you for saying all that needed to be said. I can’t even remotely understand someone not knowing. Sent from my iPhone using Tapatalk

6’ and 250 and a screen name of Beef...lose the belly and you’ll have more room[emoji12] On a serious note I have the same setup and I’m 6’4” and 265, and they could definitely use a little American engineering over in Japan. My neighbor has a B3200 with a backhoe but he has a spin around seat...

You don’t know me so you can’t say you trust me, however you have answered your own question and I’m pretty sure you know it. It’s always best when you make the decision vs. someone making the decision for you...kinda like on your terms if you know what I mean. Sent from my iPhone using Tapatalk

Jackson Big Rig-end of discussion, however not entry level price. I’m 6’4” and 275lbs and I can stand in mine. Sent from my iPhone using Tapatalk

Have a big bucket! There is no recommended fill line, rather there is a range so make sure your 1” above the upper limit mark prior to draining. Also I’m not sure on the taper of the internals but it takes a little more than 2 quarts to go from the lower limit to the upper limit mark and that’s...

Dave, I don’t feel offended at all, just the opposite in fact. I’m going to take your advise and take the tractor and brush hog up to the dealer and get a new pto shaft. Without knowing much about pto equipment I would probably buy the wrong thing if I went without it. I appreciate all the...

Thanks guys, I will just replace that bolt regardless. Nothing is seized I can still spin the gear box shaft by hand. Pretty bummed cuz I was actually having a lot of fun[emoji1] Sent from my iPhone using Tapatalk

Calm down I’m talking about my tractor[emoji16] I’ve had my tractor for a few years but today is the first time I have EVER used my pto. My friend gave me a 5’ brush hog and I decided to test it out today. I brushed hogged for quite some time then just about when I was done I hit a rock that...

The 3 point arms will have to be removed. Sent from my iPhone using Tapatalk

Don’t let it scare you, once you get past this one. normally when the flashing regen light comes on just kick up the rpms until the flashing light goes solid and keep them there until the light goes away. Takes about 10-15 minutes. Sent from my iPhone using Tapatalk

Yes that’s a regen issue and NOT a dealer issue. If it’s beeping you should not start you tractor up again until you read the manual and you are familiar with the regen process. IMHO it’s poorly explained but once you get the hang of it it’s a piece of cake. Sent from my iPhone using Tapatalk

You will have to follow the wire back to its source of power. This is important because it may be tied into an accessory, my friends was tied into his high beams. Or you blew a fuse, but you will need to check voltage at the switch. If you think its the relay , I would check it’s ground...

Have you checked for power at the switch? Where are you getting your power from? Fused? Given you problems suggest that it works at least part of the time, has it ever worked? Does it only not work on the remote switch? Sent from my iPhone using Tapatalk

Curious as to why you guys recommend filling the rear tires when it looks like his main use would be cutting the lawn with a finish mower? Wouldn’t this increase the likelihood of making ruts especially near the pond??? I don’t think he needs the ballast since he could use the tiller for that...

This post should be pinned for people who want to buy a grapple! Sent from my iPhone using Tapatalk

Just looked at your equipment list, but you don’t have an extra $150.00 for American made ones? I hope your Chinese welds never fail. Sent from my iPhone using Tapatalk