Search results

I hadn't noticed any grease fittings on mine. But I will be sure and check that the pin is in place from now on. Not sure why they randomly fall out. The universal joint was in a dry spot so I just stuck it back on and was good to go after that.

It seems to move freely. I guess its possible I ran over something that pushed the shaft up and away from the yoke. The pin must have already fallen out before that. Now you mention it that makes sense the splines would take the shear force and not the pin. I plan on buying a few pins and make...

No, the front tires are original (with tubes), the rear I replaced with same size, all turf tires so I wouldn't think they would bind much either.

I know this is an old thread but I've had this issue randomly. Today it fell off while I was in a muddy hole and had a hell of a time getting out. I've never paid attention to phase when reinstalling. Is this what causes enough binding to cause the pin to break? I've never notice anything until...

Has anyone come up with better grass chutes for their mower? I've had my Kommander Z121s for a couple of years now and the chute keeps getting torn up. I keep patching it with other pieces of hard plastic but it only lasts a few mows. I've seen sturdy types on other mowers made of thick rubber...

I replaced all the hydraulic lines 2 years ago so everything works great when running. I'l like to make mine as manual as possible so wiring around things is what I might just do....

I've got a 2003 BX1800 and almost from day one it's had it's little electrical issues. First it was the lights sometimes working, or sometimes not. Not a big deal but seemed to be showing me 'Don't leave me outside' as it happened after sitting it the rain occasionally. (I mostly keep it in my...

Saw your reply on this post, having similar issue on my BX1800. Jiggled the 3 point lift lever and fixed it. Love quick fixes. Thanks! :D Dennis

Yes that might be an option. Then there is the run a wire to the pull and just manually shut it off like that, less to fail with that method. ;)

Yeah I checked all that. Not so lucky as a blown fuse. :cool: Just hate to replace the ignition switch without testing first....

Finally got a chance to troubleshoot this and the shutoff solenoid is not getting the shutoff voltage. If I give it 12v it works fine. Now I'm just trying to figure out how to get the ignition switch off to try and test it. Cannot find any diagrams that show what holds it in the dash....

This has been an intermittent problem the past 2 years and it just started acting up again. Turn the key off and remove it and engine keeps running. I use a stick to push in the stop solenoid to shut it down. Searching through posts I see similar issues but nothing intermittent. Occasionally I...

I actually did check the spark like you mentioned and it was fine. My guess is when the plug was in the block the crack allowed it to short without sparking. Next time I'll just change all the basic cheap parts and not waste time diagnosing. :rolleyes: And I just got done mowing the entire lawn...

Might have figured this one out finally. As suggested was going to go get a new spark plug and when I went to pull the old one out again to check the number (had done so several times already) it fell apart. Must have had a hairline crack or something. Went and picked up a new one and mower...

I thought about the flooding but I let is sit for a long time between working on it. Even flooded it should fire at least sometimes I would think. Do you think the plug could be too weak? I see spark but I guess they are cheap enough I'll go pick one up just to give it a shot. Thanks!

Thanks for the reply's! Ironically my can of carb cleaner won't spray very well (lot of things breaking on me lately) but I did manage to dribble a fair amount into the carb, and still no fire. The guy at the shop said if I can see spark the plug should at least cause the engine to attempt to...

Been messing with this for several days and running out of ideas so any help more than welcome. Have mowed a few times this year already with no problems using leftover gas with stabilizer. The other day mowed for about 20 minutes and then suddenly mower stutters and shuts off with no warning...

They are indeed ghost lights. :eek: They turn on and off randomly, sometimes blinking and the switches do absolutely nothing. At one point I unplugged the switches and cleaned them. Unplugged the lights were off but after cleaning and reassembling nothing changed so I wasn't sure if it was...

I've always had an issue with my lights on my tractor and pretty much ignored it. They seem to have a mind of their own as they turn on an off, flash, or whatever no matter what the switch is on. Just curious if anyone else sees this and is there a simple fix? As long as the tractor starts I'm...

Paid around $600 for new hoses (minus 3 I had already replaced) and finally got them installed and changed the fluid and filter. Not much in the way of good diagrams so if anyone else attempts this make your own as you take the old ones off. I took a lot of pictures but hand drawn diagrams would...