Search results

If i hit the wifes new Mercedes there would be hell to pay 🤣. I drive a 54 chevy truck so it could handle a little hoe like my 750. 🤣

It can swing when plowing. It can swing when running down the road. On the trailer by law it has to have securement so i do the same … put bucket on the deck and chain it. I wouldn’t trust any hoe without both locks engaged in my shop next to my classic cars.or going down the road in traffic...

Sounds like a spun rod bearing and piston top hit head because of clearance in rod.Whatever it is good advise to shut it off and start the deep dive into motor. Pull the oil filter off and cut it open carefully not useing anything that makes metal chips ( tin snips or filter cutter). Look at...

They always catch us….🤣. Nice new toy.

2 small fab jobs to make things a little better for my woods 750 hoe. Big feet so cut off guards that no other hoes have. They were definitely ankle breakers. Now need a small weld on step. Painted were i cut. Than welded up a pin and bent a handle that i can remove from seat to lock hoe from...

Don’t feel to bad. Took my Mercedes in for an emissions recall (i do all my own work never goes to dealer). The recall had to have oil drained. Dummies at dealer over filled by 7 quarts. Only takes 7. They doubled it. Experts aint always expert.. glad you fixed it easy..

Never ever….

Might get better result by starting a new topic. This section is fabrication. Being a new guy i too had to surf around and figure out the different sections of the forum. Good Luck!!!

Nope. ATF has been used for years on injectors and other engine parts. It actually works ok. It certainly will not hurt . Used it on Detroits and Cummins. Have personally seen pretty good results.

I have seen the c mark on a different brand of motor and always seemed to line up with CAM side of block so you dont put pistons on rods wrong way. I dont think i would put new pistons in a used bore. Bore it oversized or clean up ole pistons. Pistons in ultrasonic cleaned and rings should...

Good luck. Fill the fuel filter it will help bleed the system.. quicker.Little starting fluid aint gonna hurt. Just dont use the glow plugs. Becareful on something like this that you do short cranks on starter. If it gets real hot you’ll be buying a started after you get it running 👍👍👍

If its starts on either ? you have enough electrical juice to run it.If it started water is gone from cylinders …You have a fuel delivery problem. Check fuel filter and fuel shut off. You may need a battery after it runs on battery charger. Maybe have water in fuel. Pull filter and see if clean...

Here in communist state of CT with 1 in the pipe 10 in the mag i decided on the p938 about 8 years ago. Its been a great piece. My shield was pretty badly rusted after 2 years( smith took care of it NP) Nothing but problems with kimber anything. If a kimber was givin too me i would just sell...

Nice step…. Is it steel or cast? Like to weld one to my backhoe. But not wanting to bolt it on. Cast is no go for me to weld. Great idea!

I really only do some filling, topsoil and snow removal at home so just need a good cutting edge so not chasing my tail. 👍👍👍

Thanks! Yes in the past on my skid steers i kept the hooks in line with cylinders.. also think thats the best. These light weight buckets on the LA350 loader need a bit of extra plating i think. Big PITA will be a cutting edge for bucket . Hopefully i have time to go find a suitable cutting...

Had time today to finish my snow removal lights. Ran wires thru ROP.. hate external wiring. In my business of streetrods i mostly wired them with all hidden . Wiring and hoses. Pulled a double set of wires one for ground .. one for positive. Thinking if i put anything else on ROP i have an...

I feel for you… layed on my back lots if years building race cars and streetrods. Some repair work. Not fun.. should have done it 20 years earlier. Now back is junk. Good luck with the clutch job..