Search results

My 2501 was also right on published spec. which is under L33/39 with same H pump and loader. I judiciously bumped up based on a survey of input here. I was conservative at first and couldn't be happier with the results. Felt no need to adjust further so far. Now the artificially low rev...

While I would love to have the chips for paths and projects, I separate out stove size (usually down to about 3" on "good" hardwood and pile the rest. I have become a firewood snob lately and poplar & other junk wood is not worth the time/effort. Anything I CSS (cut spilt stack) goes inside to...

Quickest & best is heavy equipment per Elliot. Trees & rocks - I have them in spades. I have time & smaller equipment and overachieve with them. I am in PA on 10 acres in the middle of about 150, sloped & heavy old growth with glacial deposit boulders of ALL sizes. I moved about 40 tons of...

Welcome! - I can't comment to the diff on the 02 vs 01 but I assume that they are comparable if not the same on specs. There are multiple routes to more power and some adjustments to use/technique. Several points to consider: The hyd pump on the 01 was the same for 25/33/39 and is underrated...

Ugh - I played a different version of the same game with the weak front hub on my 1210... I would have preferred the wheel version. FWIW - I've never seen that failure before. Maybe you can reweld?

Funny & agreed! - of course, you know that any proper oil when changed is fine. Can't resist a good oil thread... :p Use the 5W 30 or 40 depending on what's on the shelf & you don't have to worry about the season here in the NE FWIW - I run have T6 in my Kawasaki engined ZT after break-in...

FYI - you will find the same predatory price gouging on LED bulb specifically targeting kubota - not rocket science to get the specs

Dug 'em up & here you go - exact for L2501 (and others I'm sure). Paid a whopping 80 cents per. 😬 After experimenting - use a good gauge... I could have used 1 in the combo in the next size up but they were oos so I stacked them. Def. get the correct ones edit: 0.4 also available for sure...

Welcome! I bought an assortment of thicknesses to fine-tune the stack with a pressure gauge. It was expensive for the material but nowhere near what you listed above. I will check and come back, but gut-check recall it somewhere in the $10-15 range for at least 3 diff ones and multiple packs...

Wow - glad he was OK!! It is a sickening feeling that you never forget! I had this happen once on a VERY powerful older car (67) where I had just installed a new power brake vacuum line that ran under the linkage. Tested and drove fine until I did a full-throttle pass & it hung up open. Over...

This happened yesterday close to me - Was about 200+ yards of destruction and the car isn't recognizable. Talked to my friend who works at the Toyota dealership and he told me it was a Challenger. It took out the sign, two tents on either side of the drive, 10 cars including the TOP of the...

I use a 7' Handles it fine, just have to be careful on the turns ;) I would prob buy a 6'

I borrow a neighbor's 7ft beast for a stab at collecting rocks out of large newly graded areas - It generally works well, but the composition of my "soil" is partially rock to some degree. Also works GREAT for doing the same on trails and evening out erosion gullies on gravel powerline 2...

I got a sinking feeling watching it :p

Glad you were ok! I haven't had that issue yet and am in 4WD FT with my sloped property. Will keep an eye out. I HAVE taken a similar ride before on my 2WD 1210, even with fat turfs. Definitely was along for the ride and steering in vain.

Wow - I''m not sure I am getting the full picture. The weight of the rear deck swung you around...? Deceivingly, it doesn't look that steep there.

I'll go w/ Idaho Wolfman as the expert comparatively. FWIW I have the R14s and have only punctured the front but I take ALL stupid responsibility as I ran over an old C. coop with big nails. Other than that incident (on me) they have been pretty tough in all situations over rock and rough...

Not much help... but my f@rd 1210 w/16hp with 60" mmm deck cuts uphill in thick growth. Something is definitely not right.

These are ExWorks at my site - I'll load you though!

I first thought you were talking about dry stacking a wall (kinda). I started one supporting a berm near my tractor shed last spring and developed a good technique/ rhythm to place - BTW They really hurt when they shift! Nice touch on the bucket control resting them on each other. I tend to...