Search results

The tractor came back today. No word from the service dept about what they did but I do see your advice was taken and the backhoe has been replumbed to be after the the third function. When I first got the tractor I had complained how slow the hoe moved and that the stabiziler levers would...

The dealer is coming today to pick it up and I explained to the service department what I learn here from you guys. I will let you know how it turns out. Thanks for all the help!

Dan thank you very much. If you don't mind I would like to show them your post. I think your expertise should be quite useful to the techs at the dealership. The good news is the dealer has been responsive and quick to pick up the tractor for service and everything has been covered under...

Here is another photo I thought uploaded. The fitting in the photo marked with the B goes to BH valve body port also marked with a B as shown in one the other photos. It then comes out of the valve body fitting marked with a R and goes to the T port on the 3rd function. I am sorry for the...

Sorry for the duplicate posts. I am tr

There are no rear remotes and the 3pt level is in the lowest position. I double checked the plumbing. The line with the blue dustcover comes out of the pump and into the BH valve body. It then goes out via the line with the red dust cover and goes to the T port on the 3rd function valve. Then...

Thank you for all the replies. I will do some more investigating and take some photos. I did notice that the lines from the BH definitely jerk when the 3rd function is activated especially if the 3rd function cylinder is deadheaded. I will try to post again soon.

I know this is an older thread but quite relevant to my problem and I am hoping one the tractor gurus who posted here may be able to help. I have a 2023 LX2610 with a BH77 and the third function valve installed. The problem is the BH valve body keeps leaking badly. It has been back to the...

Thanks for the suggestions. Everything seems tight but hard to tell for sure where the oil is coming from. The dealer told me the first leak was a bad oring and second leak was some other seal gone bad. I sent an email to my salesman with the picture and the description of the problem. They have...

I have a 2023 lx2610 with a BH77 and the hoe valve body keeps leaking even when I am not using the hoe. It has already been in the shop for warranty repairs twice for this but the issue keeps coming back. I just turned 50 hours on the machine. It seems to leak most when the hydro fluid and...

I have the same set-up a lx2610 and BH77 and I would agree to let the dealer repair it under warranty. Mine has been back to the dealer twice in 30 hours for leaks in the back hoe control valve body. The dealer was very good about picking the tractor up and quickly getting it repaired and back...

Sorry for the delayed update but I just got my tractor back from the dealer and the problem seems to have been resolved. I had an small oil leak from the back hoe valve body and the dealer picked the tractor up. The told me there was an issue with one of the internal o-rings that caused the leak...

Thanks for the suggestion I will pull the cover take a look.

I usually run at about 2200 rpms when using the hoe. The manual recommends to operate anywhere from 3/4 to full throttle. if someone else has this same setup maybe they would be willing to check the time it takes to extend the dipper all the way out.

I have a new lx 2610 with a BH 77. The dipper speed seems slower than normal. It takes about 10 seconds to extend out. I found a spec sheet that shows on a l2501 the same BH77 should take 4.9 seconds. I had a b2601 with a hoe and I don't remember it being this slow. The other BH motions seem...

This is my take on your situation. I went from a B2601 with a backhoe to a Sany SY16 mini ex and back to a LX2610 backhoe. The mini-ex is far superior for fast digging. My current backhoe 77 seems clunky and slow in comparison although it does get the job done. I used the mini-ex a lot over many...