Search results

I think I see the difference, some models like BX use lug nuts with the cone part inward against the wheel the B models use the lug nuts with lock washers and the flat size of the nut facing the wheel. The BX style spacers come with the second set of lug nuts where as the B spacer comes with...

In the install directions provided it suggested marking the backside of the provided studs at axle flange with a permanent marking pen so one could easily inspect for a stud(s) working loose. I used a white out marker. For those that did not have to go through the stud removal when installing...

The B and BX are different. not sure why. Have not had a chance to run it, will tomorrow.

Had to remove factory studs, then Bro-tec spacers are bolted to the axle hub with new tapered shoulder bolts (provided), the studs you see in the pic are studs installed by Bro-tec that the wheel then goes on and original lug nuts and lock washers are used to hold the wheel on. These are 2 inch...

Got them installed, worked out great tires are now exact same width as my bucket. Got old studs out without damaging them. Clear coated them before install to keep them from oxidizing.

Just got this reply from Bro-Tec, Yes, that the way we design them, the Wheel must be snug, the axle flange is done with the hardware taper lug bolt to properly center it to the axle. Richard

Will get a pic, but yes it is a lot of play.

Installing my Bro-Tec spacers, and have a question. Is the spacer supposed to be concentric to the axle and the wheel? I have .110 thousands difference between spacer and axle hub flange (loose). The spacer is concentric to the wheel opening. I put a call into Richard at Bro-Tec but have not...

Bro-Tec website is now up and working.

I ordered (they did not stock at store) from Ace Hardware, spring number SP9668, when I ordered the website had it listed under Prime Line SP9668 when I picked it up it was packaged under the name of Handy Man SP-9668 not sure why but the spring specs were the same. This spring needs one end...

I replaced the the return spring on the linkage today on my B2601with a lighter (tension) spring and it made a noticeable difference on the effort needed to depress the pedal. I am not a big man so every little bit helped

I am in the same situation as you with the same tractor, I looked on the Kubota build site and it is a $482 option. To me that is way too much money. The Bxpanded brand barracuda thumb is $370 which is a little better on price. Not sure if there are any other aftermarkets available. I have...

Unfortunately the B2601 has a uncommon bolt pattern that does not match trucks /Jeep bolt pattern. Believe me I looked. Thanks

Well I contacted Richard at Bro-Tek by Email and got a quick reply, He stated their website was long over due for a upgrade and it should be up and running again this week. They did have the spacers in stock and ready to be shipped, unlike Bora that states 4-6 weeks unless you want to pay for a...

Thanks, will wait a couple of more days and if no luck with their site I will go with the Bora spacers.

Well not having any luck getting Bro-Tek site to come up, does anyone have any idea how much they charge for the 2 inch aluminum spacers for the B2601?

I have looked at the Bora spacers, I was just going to compare the two brands and make a decision.

Wanting to buy some 2 inch wheel spacers for my B2601 and I have read nothing but praise on Bro-Tek spacers. My problem is when I click on the link that others have posted I get "not secure" site. Have tried changing my settings but no luck. This is the link I am using, any suggestions...

Picked up my Used (60hr) B2601 FEL / BH70 this evening. 9/27/2020

I did a little more research last night and found a Kubota dealer that sells a kit that includes the FEL bracket and and a weld on bracket to change up the pin on bucket for $775. I would think one could buy the FEL bracket ($440) and the factory QA bucket ($460), and like you said sell/trade...