Search results

I lube the bearing plate that the chute sits on before/after each season, that's where my noise comes from on a rear blower. the rotator teeth are so far apart any lubrication wouldn't stay on. I do hit the handle guide tube whenever I do the chain.

Check that the three point hitch control is in it's neutral position. I have a rear snow blower and sometimes I leave the lever in an up position and then there is no hydraulic flow to raise the loader. When clearing my drive I plow forward and snow blow backwards. The constant raising and...

I'VE HAD FIVE, AFTER 75 NO NEED FOR ANYMORE WITH NO INDICATION OF..WHATEVER... WAHOOO! NO MORE PREP. BUT MY WIFE WILL NOT UNDER ANY CIRCUMSTANCE SUBMIT TO IT. SHE HAS SEEN ENOUGH... THEY WOULD GET A LOT HIGHER RESPONSE RATE IT THEY TOOK YOU IN THE NIGHT BEFORE, GIVE YOU A FEW DRINKS...

I have the Titan box as well. It came with the correct pins in Red also. I added two more plastic pipe tubes on the far side before I filled it with sand. I carry the rake, hoe, shovel and tamper for road work in them.

I've been burned by Chinese copies before. I opted to look for a used Wallenstein at the same price as the new clones. No problems to report. It was used to clear the owners house lot and then sold.

I read it differently: Drawbar load is 1/3 of the tow load... 730 #/ 2200#. That is the normal 1/3 hitch weight of Gross towed load. I think the confusion is in the "Trailer loading weight" caption. I would have worded it "Total trailer weight, including load" On a more common sense...

GREAT IDEA!

I agree, but I have not had a problem to address in four years of KX-018 use. Most of my user questions get answered here: Letsdig18 https://www.youtube.com/channel/UC-NlyhOdTK4C30NhptvD7UA

I've been using my 5 foot Meteor blower on my B7610 for many years. I almost bought a B2650 this summer but I do not want R4 tires. After looking around some more, everything was sold. I just spent 3 hours yesterday and 2 hours today driving backwards clearing our driveway and 1/2 mile private...

How is the tire clearance on the front with the wheels turned fully? On my B7610 the front tires hit the loader frame.

I second the Pat's Quick hitch. I'm too old to horse around the implements and they are not quick hitch compatible.

I think it's a farrier's tool, a nail clincher/hammer. I remember one hanging in our barn.

One consideration is the slope of the road you are plowing. I have a steep 1/2 mile gravel road that I plow downhill and then use the rear blower going back up. I found that i needed to angle the blower upwards more to not ingest so much loose stone. On the level that leaves a lot more snow behind.

Watch your turning radius for the tire hitting on the inside if you have a loader. Wish I had know about it first. It took one half turn out of my steering wheel and there is no stop bolt to limit the steering. I deflated a tire in 18: of snow because I couldn't see the wheel.

I can't speak for the mower, but you need to watch the loader frame. The wheel spacers make the tire swing a bigger arc around the spindle. I lost a great deal of turning radius when I added them to my front hubs.

Had one for three years now. My wife loves it for running around our 75 ac. If you have any hills you might want to try it out first. Everything here is a side hill and it will not go up in high gear, even empty. We use it to run to the mail box, 1/2 mile down like a ski jump...Other than lack...

IF YOU HAVE ROOM TO GO IN BOTH DIRECTIONS, I USED TO GO THE OTHER WAY TO FILL THE DIVOT AND THEN NEAR THE OTHER END LIFT THE TILLER OUT SLOWLY BEFORE THE END.

Another warning about front wheel spacers: My B7610 front tires hit the FEL mount pillars at full excursion.

One thing I thought of that could have caused the problem was if the owner did not cut the PTO shaft to the correct length and raised an implement,it could punch the shaft back into the casing and bend the forks. I have had to cut a large amount off the shaft of all the implements I bought for...

I'm afraid I can't be of more help, I've never been inside one of these before. https://www.messicks.com/ku/84622?sectionId=215777&diagramId=330819 https://www.messicks.com/ku/84622?sectionId=215777&diagramId=330820 https://www.messicks.com/ku/84622?sectionId=215776&diagramId=330817...