Search results

It's from the top clutch bracket just above the zerk fitting leading to an 1 1/2 x 12 inch angle that runs side to side. I just repaired this angle as it broke and had to weld it to repair. Have fun reattaching it, it's a bear to do. And thank you, for I was under my B3300su tonight with a...

Yes, it's called the Operator Presence Control (OPC) system. Had the same problem on my B3300SU. The switch is located off linkage to the HST pedal. If you have to rock the HST pedal to get it started, this switch is hanging up. You will have to look for it, it's high up facing forward and has a...

What Variant is it, F, DT, GST or HST, this would help.

The OPC is above that in picture on my tractor, hard to see, look farther back, too. You may see some wires leading up to the switch.

Check the Operator Presence Control (OPC) switch located off the linkage to the speed control pedal. I had same problem and lubed the switch while moving the pedal from below the tractor. The OPC switch should be depressed while the speed control pedal is in the neutral position and pop out when...

should cost about $80. You do not need to replace the hydraulic fluid at this maintenance cycle. Change engine oil and filter, change transmission oil filter, very little will drain out when filter is removed, that's the filter on the left side, #HH660-36060. The rest is basic maintenance.

Welded two hooks on by FEL with MIG, worked great, did not unhook anything, ground close to work.

I have a DRpower 3 point hitch chipper. 19 hp to 65 hp, Category 1 - 3 point hitch, fly wheel is 16.5 inches, 3/4 inch thick 55 lbs. Takes 4.5 inch branches with ease. I bought the extended chute which I use to blow the chips into the back of my truck. Very happy with this product, no problems...

My B3300 has a swivel seat for a BH76. The dealer installed when I purchased tractor with backhoe mounted, may not work for your model. Worth checking out or at least getting some ideas for your own seat.

Clockwise is slow, Counterclockwise is fast. Clockwise to the stops is locked.

Agree with KB above, my B3300SU (has a clutch) and have to press the HST pedal forward and back works the best.

Hope you were using the Battery Tender JR. which is 750ma, normal motorcycle size battery charger. Battery Tender listed above for a tractor is 1.25 amp. Using the correct tender for the size battery will NOT boil your battery.

Battery tender is the way to go, comes with two leads, the clip type and bolt on type, both have in-line fuses. I routed mine through the front grill. I have 5 total tenders, all have kept my batteries at top condition for 3 motorcycles and electric start generator (smaller wall plug type) and...

the switch is located just forward of the Hydraulic filter on the right side, hard to see as it's up high. Just follow the linkage from the HST pedal.http://s896.photobucket.com/user/ivanbunker/media/Kabota%20OPC%20switch/IMG_0195.jpg.html?sort=3&o=1

OPC (Operator Presence Control) switch is engaged by a linkage from the HST pedal. If the HST pedal is depressed and the operator leaves the seat, the tractor will shut off. If you find that is not the case, you need to get under the tractor and spray lub on the linkage and switch button. When...

That switch is called Operator Presence Control, when HST pedal is in neutral, this switch in depressed (linkage fails to depress switch, tractor will not start). Spraying the linkage to this switch from the HST pedal and the switch button with lubricant will keep both working properly, do this...

HH660 left side, not much oil will escape, do this at 50, 200 and 400 hours. HH670 right side, removing this will drain most of tank, no 50 hour service, only at 400 hours, also at 400, hydraulic fluid replacement along with transmission strainer cleaning.

Have HST B3300SU. The left filter is the Transmission (HST Filter) and the right is the Hydraulic Suction Filter (Hyd, system) My part numbers are different as yours should be for each filter, not sure what the difference would be unless one has a magnet (Transmission), would make sense for...

My B3300SU has two hydraulic filters, one for the transmission and one for the hydraulic system that operates the bucket and backhoe. Transmission on left side and hydraulic on right, both by the rear tires. The transmission can be removed without draining system, but the hydraulic filter will...

Thank you Kallred. I assume all tractors have an OPC (operator presence control) safety switch. The switch operates (shuts off tractor) when the control pedal is pressed and the operator leaves the seat. My manual lists a test of this switch, tractor running and pressing the control pedal...