Menu
Articles
Forums
New posts
All threads
Latest threads
New posts
Trending threads
Trending
Search
Search forums
Search profile posts
Members
Current visitors
New profile posts
What's new
New posts
New profile posts
Latest activity
Latest threads
New media
New media comments
Classifieds
Media
New media
New comments
Search media
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Latest activity
Account upgrades
Register
Menu
Tx Jim's latest activity
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
T
Tx Jim
reacted to
North Idaho Wolfman's post
in the thread
M5700HD Shuttle Issues
with
Like
.
Have you checked this pressure relief valve?
Sunday at 3:11 AM
T
Tx Jim
reacted to
whitetiger's post
in the thread
M5700HD Shuttle Issues
with
Like
.
The bad news is that when the forward pack was operating with low pressure, the clutch pack was slipping and has toasted some of the...
Sunday at 3:10 AM
T
Tx Jim
reacted to
TheOldHokie's post
in the thread
Hydraulics at the rear m7060/m4509
with
Like
.
I am a little confused by the question. Did you plumb the backhoe as shown below? Dan
Friday at 3:01 AM
T
Tx Jim
replied to the thread
M7040 3pt
.
My guess is if 3pt raises higher when draft control lever is moved rearward after 3 pt control lever has been moved fully rearward is...
Aug 11, 2025
T
Tx Jim
replied to the thread
Hydraulics are too fast, or Im too slow
.
Several yrs ago while handling rd bales with a Kubota M4900 with Kubota FEL I added an adjustable hyd flow control valve so boom...
Aug 6, 2025
T
Tx Jim
replied to the thread
M7060 - 3-Point Hitch control lever at the rear of tractor.
.
Evidently you do not utilize the feature of the built in extendable draft link where one can extend & raise ball when attaching...
Aug 4, 2025
T
Tx Jim
reacted to
OntheRidge's post
in the thread
M6-141 50 Hr Service....15 GALLONS of Hydraulic oil? Don't Think So!
with
Like
.
Hmmm, 125k tractor, not worth $420 worth of hydraulic fluid?
Aug 4, 2025
T
Tx Jim
reacted to
WI_Hedgehog's post
in the thread
M6-141 50 Hr Service....15 GALLONS of Hydraulic oil? Don't Think So!
with
Like
.
The mating surfaces of new gears wear in, shedding microscopic metal bits in the process, which cause significantly more wear than gears...
Aug 4, 2025
T
Tx Jim
reacted to
North Idaho Wolfman's post
in the thread
M5040 3 point hitch
with
Like
.
It's not a hydraulic line connection, it's near to impossible to change the flow of that system. Your not adjusting the draft control...
Jul 31, 2025
T
Tx Jim
reacted to
TheOldHokie's post
in the thread
M7040 3 point weakens throughout the day
with
Like
.
Here is a basic test rig. Right end goes to pump delivery and left end goes to sump. You hook it in, open the flow control valve to...
Jul 29, 2025
T
Tx Jim
reacted to
TheOldHokie's post
in the thread
M7040 3 point weakens throughout the day
with
Like
.
Yes, in this case you can just replace the factory U-tube with the test equipment. I will get this made up ASAP. Are you OK with male...
Jul 29, 2025
T
Tx Jim
replied to the thread
Kubota L3400 Vapor Lock???
.
Many yrs ago I owned a M4900 that after operating for while would loose power. After performing many diagnostic procedures I consulted...
Jul 29, 2025
T
Tx Jim
reacted to
North Idaho Wolfman's post
in the thread
Kubota L3400 Vapor Lock???
with
Like
.
Depends on the amount of algae / bacterial growth and type of biocide you use. The stuff I use eats it up and breaks it down so it get...
Jul 29, 2025
T
Tx Jim
reacted to
Russell King's post
in the thread
Kubota L3400 Vapor Lock???
with
Like
.
Does a biocide break down the slime (clean out a plugged line)? Or does it just kill and stop further growth? Does he need to clean...
Jul 29, 2025
T
Tx Jim
reacted to
North Idaho Wolfman's post
in the thread
Kubota L3400 Vapor Lock???
with
Like
.
Seafoam is not biocide, it will not get rid of algae/ bacteria in the tank or lines.
Jul 29, 2025
Top
Bottom