Menu
Articles
Forums
New posts
All threads
Latest threads
New posts
Trending threads
Trending
Search
Search forums
Search profile posts
Members
Current visitors
New profile posts
What's new
New posts
New profile posts
Latest activity
Latest threads
New media
New media comments
Classifieds
Media
New media
New comments
Search media
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Latest activity
Account upgrades
Register
Menu
ruger1980's latest activity
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
R
ruger1980
replied to the thread
Maple tubing supplier in SW Missouri?
.
Please see the map I added of the native range of the sugar maple.
Jan 20, 2025
R
ruger1980
reacted to
North Idaho Wolfman's post
in the thread
Tire fill
with
Like
.
Over full would not have hurt it one bit.
Jan 19, 2025
R
ruger1980
reacted to
GeoHorn's post
in the thread
Everything on Everything Attachments
with
Like
.
Has EA / ”Ted” yet made-good yet on all the product for which he was paid and never delivered….?? Or, has he contacted those folks and...
Jan 19, 2025
R
ruger1980
replied to the thread
Maple tubing supplier in SW Missouri?
.
This is the native range of Acer saccharum
Jan 19, 2025
R
ruger1980
replied to the thread
Old style PTO shaft compatibility
.
Yes you can get square pto shaft parts. Bothe male and female ends. I would measure it first as they do make rectangular sliding shafts...
Jan 16, 2025
R
ruger1980
replied to the thread
L2550 - Hard starting at all temps
.
I am not making claims I am just reiterating what Kubota says about their own engines. The snip I added is right from the WSM and the OP...
Jan 16, 2025
R
ruger1980
replied to the thread
L2550 - Hard starting at all temps
.
One more question, does it start better if the throttle is at full fuel? If so there could be an issue with the start spring in the...
Jan 16, 2025
R
ruger1980
replied to the thread
L2550 - Hard starting at all temps
.
Sorry I was preoccupied. That may have the correct adapter but hard to tell as I don't have the thread dimensions for your glow plug.
Jan 16, 2025
R
ruger1980
replied to the thread
L2550 - Hard starting at all temps
.
Those measurements are better. It does seem a little slow. Can you measure cranking voltage at the starter? It is showing smoke while...
Jan 16, 2025
R
ruger1980
replied to the thread
L2550 - Hard starting at all temps
.
Yes double check your readings. As a general rule diesel engine need to turn about 150rpm to reliably start. If it cranks wickedly fast...
Jan 16, 2025
R
ruger1980
replied to the thread
L2550 - Hard starting at all temps
.
If your measurements below are accurate I would be surprised the engine even turns over. The measurements in yellow show an incredible...
Jan 16, 2025
R
ruger1980
reacted to
jimh406's post
in the thread
Best advice wanted for blading snow
with
Like
.
Add chains to the rear. That will help your traction issues because if the rear tires grip unequally you won't go straight. For even...
Jan 12, 2025
R
ruger1980
replied to the thread
Rear remotes loose
.
That snap ring is twisted. get a new one and lose the pipe tape on the fitting. Snap rings have a sharp edge on one side and a rolled...
Jan 11, 2025
R
ruger1980
replied to the thread
Tire ballast choices
.
You must live on Long Island or downstate.
Jan 9, 2025
R
ruger1980
replied to the thread
Tire ballast choices
.
What keeps the sand from freezing in the pile?
Jan 9, 2025
Top
Bottom