Yeah... I "USED" a wrench to "FIX" the broken tie rod on my L3400HST.
Dooohhh....
I drove it 50ft to the garage to really fix it.
Dooohhh....
I drove it 50ft to the garage to really fix it.
What did you do to or on your Kubota today?
- Thread starter gurn
- Start date
bcbull378
Member
Equipment
GL3830,fel,brush hog,pallet forks,disc,gannon,auger,springtooth,plow,drag,ripper
I removed brush out of a ravine today and reworked some dirt roads for a customer. The photos are before and after photos of the ravine. Love my Grand L3830.
Attachments
I pushed over a big-ol buckthorn and came down on the root ball.
I have about 7 Ac with many over grown trees-weeds. I have been waging war on the buckthorn and this one bit back. They are going to pay! Actually I have to pay, for a new tie rod...
Put on a hydraulic top link.
Would you be willing to give us the brand and model number of the hydraulic third link
Thank you in advance
Sent from my iPhone using Tapatalk
Sure. Its this one
http://www.agrisupply.com/top-link-cylinder-cat-1-20-to-28-in/p/90599/
The rest of the parts were picked up from my local TSC.
Last edited:
Yah. But its on a valve thats got a float function. I don't think float and check valve work together.
Performed first service on my BX2370-1 today. Changed the oil & filter and the transmission filter. Used OEM oil and filters. Wasn't quite due only 46.5 hours, But I wanted to get it done before I put the MMM back on. Got it on and ready for mowing season.
Added rear power terminals, 50amp from battery. 6 gauge wire from jumper cable 50 amp fuse and stud terminal ends with wire protector. Hardest part was routing the wire and most time consuming was bending and drilling the 16 gauge metal mounting plate.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Nice clean work. What can you use the terminals for?Added rear power terminals, 50amp from battery. 6 gauge wire from jumper cable 50 amp fuse and stud terminal ends with wire protector. Hardest part was routing the wire and most time consuming was bending and drilling the 16 gauge metal mounting plate.
Sent from my iPhone using Tapatalk
David Page
Active member
Equipment
1974 L260, 6" bush hog, subsoiler, spring tooth harrow, boom pole, 2 bottom plow
Saturday I charged the battery and started and ran the tractor for a few minutes. There was still to much snow to move it around, but it sounded good for a two cylinder.
Yesterday I mowed my girlfriends lawn for the 2nd time. She lives in town with a tiny lot. I'll bet I looked funny with a "lawn mower" that size. I just may buy a cheap used lawn mower and keep it at her house. Too much for my aching body to do with a push mower, but the Bota is a bit much.
Also mowed some of my lawn for the 4th time this year! I had sowed some winter rye and it grew a LOT higher than I was told it would! Well the dogs helped with the fertilization.
I still can't believe how well it cuts for how quiet it is. I swear my deck has a silencer built in! It sounds like the blades are hardly turning.
Also mowed some of my lawn for the 4th time this year! I had sowed some winter rye and it grew a LOT higher than I was told it would! Well the dogs helped with the fertilization.
I still can't believe how well it cuts for how quiet it is. I swear my deck has a silencer built in! It sounds like the blades are hardly turning.
Thanks
Pump, Sprayer, winch, other DC powered things.
Even put trickle charger on it when parked
Sent from my iPhone using Tapatalk
This morning I lugged out the block and tackle chain and tie downs,, And pulled out several old apple trees that had gone on to meet the wood pile. And planted 6 new ones, I might get anything off them but the next guy should get a bunch of apples