New profile posts

Looking at a 2022 ZG227 with only 49.2 hrs.
2-3 acres twice a month for 8 months a year in Fl.
Will be due for 50 hr service if bought.
Paid $9800 asking 7500 then 6000 I offered 5k and said come get it.
2 hr drove. Owner died or so they say.
Have JD M655 Zero now and like it but getting old.
How are these holding up? My understanding is the biggest machine before going to diesel?
They say this is the "overlooked" model?

Snowblower BX2750D problem removing auger shaft. I have a 2010 BX25d with a snowblower that tried to eat a block of wood hidden under the snow. I already replaced the broken chain and gears. It appeared to work fine, no sheared pins, but
augers spin intermittently. I removed augers but am not having any luck removing
the auger shafts from the gear casing. I was hoping to get a look inside the gear casing to see what could be causing the problem. Tried hitting casing to move it off shaft but not working. Any idea what could be keeping the case from moving on the auger shaft? Can heat be applied to the gear casing?
Any suggestions would be greatly appreciated!

Kubota BX1850, Kubota BX2750D

Thanks so much for the reply on the height and pic. When mine arrives next week, need to verify it has the oem step. If it is, I'll get that used one on E-Bay, and double up. Asking $60. Pretty dirty, will offer $35. New are $105. Can't wait for an enclosed cab finally. Will see if I can store the glass doors in my shop for the summer, or at least maybe make a prop to hold them open on nice days. Time will tell to get used to it. Better than sitting on the old open horse I did for decades.

hi, working on my bx1500D RIGHT NOW WITH UDT TRANSMISSION FLUID LEAKING ON FRONT AXLE. i AM SURE I NEED TO REPLACE SEALS ETC ON THE AXLE BUT I HAV NOTICED WHAT LOOKS LIKE OIL ON THE INSIDE OF MY FRONT LEFT TIRE. COULD THERE BE SOMETHING INSIDE THE TIRE THAT COULD BE LEAKING OR MAYBE THE OIL THAT WAS LEAKING FROM THE FRONT AXLE CYLINDER WAS SPITTING ON THE WHEEL WHEN I TURNED IF? AGAIN I AM AN 81 YEAR OLD FEMALE WHO HAS WORKED ON MY TRACTOR AND I HAVE ABOUT 14000 HOURS ON IT. SHE IS BANGED UP BUT IS SO DEPENDABLE FOR ME TO STILL DO WORK ON MY 5 ACRES. I HAVE BEEN USING THE FRONT END LOADER A LOT MOVING TREE STUMPS AND FIREWOOD. i hAVE WORKED THIS MACHINE OF MINE A LOT AND SHE IS SO DEPENDABLE. i WANT TO GIVE HER THE BEST TREATMENT BEFORE I TAKE HER TO THE SHOP TO BE WORKED ON

Regular Attender

Ok, I'll take the frame if it's not mangled. It looks ok!
Just send me your PayPal info.
Frank
1fmgsr@gmail.com

Hey new member here. Have a BX23S (just a few years old, well-maintained) with BX2830 snowblower. having an issue with engine wanting to Peter out/lose power. Both fuel filters were changed recently so that shouldn't be the issue. Also already have kubota anti-diesel additive running through fuel system, so should be good there. does anyone have any ideas? thanks for any timely input as it would sure be helpful to have this thing working in time for the storm!

Hey lance, do you have any fenders that would fit a l275? Or a hood by chance.

Hi,

I was wanting to put a hydraulic thumb on my L35. I was reviewing raleighl35's post where he did this. Someone else on foreum suggested he doesn't get on forum much and for me to maybe contact you since you might have installed the modification yourself and could maybe answer any question I had. I understand you have to add a valve. He said it was a Husco 5002-a1 valve. How do you attach that valve to existing valve bank. Is it with a longer tie rod. If so where do you get that. Also he said the control pedal and parts needed was from a Bh92. Do you know the part numbers I need to order? Is there anything else I might need to know other than what was in his description of the install? Thanks for helping..

covered the whole tractor. then use a propane heater for approximately 1 hour then it work; thanks it was code 20

Got a LX3310 now

Hello sir are you looking to sell parts off any these? I"m looking for a a front bevel shaft 38520-43460 for my L345dt. Thanks, I'm jealous of you having all those!

I'm trying to figure out how i can connect a 3pt hydraulic log splitter to my tractor hydraulics using my connections at my front end loader. Can I connect them directly using long hoses? if so which two do i use?

How can I contact you directly to negotiate a purchase?

Before I send your ad for the BX1880 to my brother-in-law, do you still have it? Thanks!

I need a regulator for a L260. Do you have one?

Je suis intéressé par un jeu de housses d'hiver pour mon L6060. Pourriez-vous me contacter pour connaître la procédure de commande ?

Here is a shop manual

good morning, i have a mower, ZD-1011, with a D782 kubota engine that is no good due to cracks on the head valve, however i do have a D1005, thats i just rebuilt , can any one tell me if i can use my D1005, and replace the D782 , any major chances that i might face? any feed back will be much appreciated,