New profile posts

Bulldog a saw that you responded to a post about a type of loader for B7100. I have the same issue with mine.
I can’t seem to figure out how to upload the pictures of my tractors loader. But what I can tell you is that the control lovers are small and or directly behind the arm, which has a fill cap for the hydraulic fluid.

I'm looking for a copy copy of the B26 service manual...Gary

Learning about my new BX23S

I finally finished this thing. I was able to locate the last bearing/bushing, metal crank pin #1 in Australia of all places and got In. & Ex. Valves from them as well. The parts were Japanese but not necessarily Kubota so im unsure but they were quality parts. I sourced a new crankshaft, used rods almost locally and all the seals, gaskets, pistons, ring packs main bearings, rod bearings and bushings from good ol' Messiks. I installed new valve guides, reamed them, I re-cut the valve seats, new valves, glow plugs, and re-sealed the chassis so there's no mess when its parked. I was also able to find NOS fuel camshaft kit on eBay. The sleeves on the other hand were no more than .0002" out of round. I was absolutely blown away at the fact.

There is alot about this site I don't understand. I have not been very regular about signing in.
I have gotten some good info. Just posted a note about my "growling" right rear B3200.

I just bought a 2025 L4060 HSTC to replace my 2000 L4310 HSTC. This tractor is taller than the old one. It is a long stretch for my old legs to the step. Any way to replace the step with a lower step or even a two level step. There is a company that makes a two level step but not for a cab tractor.

Looking for a ROPS for L245DT. Can you help out?

New owner of Lx2620SU

Its coming along, I went to my machine shop in town and they said they'd make me a 15231-28470 and good thing because I've searched everywhere without an success. Tranny filled to the brim with diesel and it sat for a week after it was drained, vacuumed the sump to capture any debris and got it painted. its not extremely accurate coloring but looks decent. Crankshaft was completely destroyed, it was ran for some time without #1 rod bearing and the rod journals were 4 tenths of an inch different in diameter... Sleeves are .0001 out of round so were going for another 50 years on em. Everything I need to overhaul this little guy is in the mail, between eBay and Messiks I got everything I needed and then some. I'll keep anyone following along in the know.

BH75 backhoe
I am having trouble finding seal kit for 'ol orenge outrigger cylinders, 30 R x 65 B....

I have an old B7100 HST E and the steering locked up yesterday. I saw your posts in the thread on "Fast B7100" from April/May of this year and wanted to reach out to see if you might have that part. I believe the HST box is different from the non-HST. Thanks!

L3800; Hydraulic oil check; is there an alternative way to measure the oil level other than the ridiculous window and it's placing ?
The window always been difficult to see but now it's opaque as if blinded. I"m considering draining the sump and refilling with the correct level of 6.2 gallons , it won't solve the problem for future level checking. Any suggestions would be gratefully appreciated!

I have a older Kubota with low hours( 360) was just sitting there warming up and then just died. Now when you turn key to first position it makes some weird noise like relays chattering and when you go to glow plug warm up position the light comes on but when you go to start position, nothing. Any ideas?

Thank you, Hugo.

Hello I am looking for a used engine for a M8540. Where is the best place to fine one?

Currently noticing that I have been a member since 10/2021 and I am also a New Member.

Wishing the hydraulic tubes on my loader were numbered by order and position in which they should be installed and their final position inside the channel of the loader arm….

Looking for wiring harness for L345, do you have one?

I bought a hydraulic pump for my B8200hst tractor and found when it was delivered I bought the wrong one. Do you happen to still have a left rotation pump?