New profile posts

Had the same issue on my new BX. Dealer stated the rubber stems were no problem, Rimguard said they would eventually fail. Rimguard was right, they lasted 3 years. Dealer was gone so did some research and came across Colby Valve company. Replaced both stems with Colby Extra Short brass valve stems and have had no problem since, over 8 years now. Colby stems can be installed without removing or breaking down the tire, the reason I used them. Lost approximately 1/2 the beet juice in the tire that blew the stem, probably 1/3 in the other, have bolted on wheel weights now to offset this loss.

L3800; Hydraulic oil check; is there an alternative way to measure the oil level other than the ridiculous window and it's placing ?
The window always been difficult to see but now it's opaque as if blinded. I"m considering draining the sump and refilling with the correct level of 6.2 gallons , it won't solve the problem for future level checking. Any suggestions would be gratefully appreciated!

I have a older Kubota with low hours( 360) was just sitting there warming up and then just died. Now when you turn key to first position it makes some weird noise like relays chattering and when you go to glow plug warm up position the light comes on but when you go to start position, nothing. Any ideas?

Thank you, Hugo.

Hello I am looking for a used engine for a M8540. Where is the best place to fine one?

Currently noticing that I have been a member since 10/2021 and I am also a New Member.

Wishing the hydraulic tubes on my loader were numbered by order and position in which they should be installed and their final position inside the channel of the loader arm….

Looking for wiring harness for L345, do you have one?

I bought a hydraulic pump for my B8200hst tractor and found when it was delivered I bought the wrong one. Do you happen to still have a left rotation pump?

I am trying to get a shipping quote from Valley Cartage, but they need name and delivery address. If you are still interested please send your contact information. Thanks.

BTW: As I mentioned in the original post this valve will run the "UP-DOWN" function on the BX2200 snowblower but it does not have enough hydraulic connections to run a front end loader (FEL).

I have a Kubota T2290KW 42" with a mulching kit and I am attempting to reinstall the mower belt which came off while going over a bunch of branches. The manual is not very helpful. My question is when reinstalling the mower belt ,does the belt get installed between the pulley and the guide pin or does the belt get reinstalled on the outside of the guide pin. Please help!!!!!@

Trouble withB7200 4WD
Over past several months 3 point hitch getting weaker and not going as high. 3 point will also not stay up and leaks down, Fluid good and screen clean……tractor 35 years old….pump going out and bypassing internally ? Suggestions
Tomt

great remedy to buying a new tractor. Have you come up with a price and or a video to do the install including you're parts?

Just acquired a G1800.

Have purchased all of the parts to replace everything connected to an overhaul of the the Loader Lock Lever. What do I remove in order to gain access to the guts of the Lever on this 2007 L 4240 D HST with LA 854?

The loader joystick works fine until the valve lock moves from being in the unlock position and then the joystick resumes working again.

szia, Kubota b6000 probléma. alapjáraton kéken füstöl, ha nem állítom be a dekompresszor csavarját a ventilátor oldali szelepen. de ha úgy állítom be, hogy kicsit hozzáérjen akkor nem füstöl kéken. se olajat, se vizet nem eszik. új karburátorokat adagol. szelephézag beállítva. mi lehet a probléma?

still here still playing with my b7000 and the B7100 trying to find the right gauge for the battery cables the old ones are worn off too much to tell

I am looking for engine panels for a L3010. Would you happen to have or know where I can find some ? I don’t want to purchase new. Thanks