New profile posts

Wanted to respond to a question you had about my 3rd gen bucket if you're still curious. The 3rd Gen bucket added "High Dump" bracket to give it better dumping capabilities. The 2nd Gen was a complete redesign of 1st Gen to make it less expensive to build.
need help with my gr2100 snowblower
K
k countryman
Have a lx3310 with 51 "front mount snowblower. Deflector is actuating , but chute rotation doesn't regardless the position of toggle switch. Toggle located on lever in cab. Loosened hydraulic connections and no obstructions and can turn chute by hand. Fuses are good. Any suggestions.
I have a B2630 I purchased new in 2011 the receiver end of the seat belt quit holding the ratchet in place I can hear it snap in place but a nice tug and it pops right out.
I am looking fo a replacement receiver end.
Mountainman
Mountainman
Thank you for the inquiry but unfortunately i wouldn't have any b2630 parts or anything that new.
Find a snow blower for your B7800?
B
b12
Yes. I have a Frontier SB1164 rear mount snowblower.
Where can I find a cheaper alternator for my BX23S. I only see them for $350
S
Scott323
My tractor battery light came on and was reading 18volts. I think I need a new alternator
Kubota u173a. 2012
All works ok apart from arm and tracks which I assumed was a faulty safety switch, I have checked this and all is ok, If I give it full revs I get minimal track movement and arm movement, I have removed the hydraulic pump and spline etc all intact so could it be the solenoid off the safety switch? If so where would that be located? I would very much appreciate any advice
Regards
I have an L245Dt and I am looking for the left side axle. My manual has a part number of 35110-2711. Does anyone out there have a used one for sale?
Thank you!
T
Tcmk
007kubotaguy has the parts you need .
Kubota u173a. 2012
All works ok apart from arm and tracks which I assumed was a faulty safety switch, I have checked this and all is ok, If I give it full revs I get minimal track movement and arm movement, I have removed the hydraulic pump and spline etc all intact so could it be the solenoid off the safety switch? If so where would that be located? I would very much appreciate any advice
Regards
I have a Kubota B2400 it is loosing power especialy in high gear I have changed fuel filter, fuel pump both new injectors, checked the timing gears, but does not have enough power when driving, will stall out without a strain, could it be hydraulics, i have the kubota servic manuals but can not figur it out, any help would be appreciated thanks
D
Daniel Pullum
I had a B2400. It had 85 hrs when I bought it from the dealer.
At 600 hrs the hydro peddle went nuts. The tractor would run/move until I dropped the scraper and the peddle hammered like a machine gun.
The dealer checked out, with no solution and called Kubota Central Service Center. A rep went to the dealer and made them repeat all the tests (mostly hyd pressures)they had performed. The service rep told them to give me full value on whatever I wanted. He took the machine back to headquarters. Quite a time elapsed before we got an answer. Wait for it on the next line.
THE WEAR PLATE BETWEEN THE PISTONS IN THE HYD PUMP WAS MISSING. THAT MEANT THE PISTONS WERE BEING PULLED .461 TOO FAR IN THEIR BORES. Probably built on Friday or Monday by a subsittute assembler.
Hi Fried, Thanks for various helps online.

Saw you have Fords and an 8N. Here's a photo I took 4 years ago as my friend Buck Spooner down the road finished a restoration for a customer:


Regards, Terry
  • Like
Reactions: 1 users
hello to anyone who might own a G6200 kubota with a 3 cylinder
it stop running and cannot move it other than lifting the rear end off the ground
does anyone know if that 1989 has a nutural gear to be pushed
sure help if i can find that out
thank you all that reading this
F
Firefight100
There is no neutral. You will have to lift the rear to move it or put it on a trailer.
  • Like
Reactions: 1 user
Have a b5200 need to replace glow plugs and glow plug incator new key swith belive key turns to left to make glow plugs to work