New profile posts

I have an L245Dt and I am looking for the left side axle. My manual has a part number of 35110-2711. Does anyone out there have a used one for sale?
Thank you!

Kubota u173a. 2012
All works ok apart from arm and tracks which I assumed was a faulty safety switch, I have checked this and all is ok, If I give it full revs I get minimal track movement and arm movement, I have removed the hydraulic pump and spline etc all intact so could it be the solenoid off the safety switch? If so where would that be located? I would very much appreciate any advice
Regards

I have a Kubota B2400 it is loosing power especialy in high gear I have changed fuel filter, fuel pump both new injectors, checked the timing gears, but does not have enough power when driving, will stall out without a strain, could it be hydraulics, i have the kubota servic manuals but can not figur it out, any help would be appreciated thanks

Hi Fried, Thanks for various helps online.

Saw you have Fords and an 8N. Here's a photo I took 4 years ago as my friend Buck Spooner down the road finished a restoration for a customer:


Regards, Terry

Tractor is in 27527 zip, Archer Lodge, NC. Raleigh area.

hello to anyone who might own a G6200 kubota with a 3 cylinder
it stop running and cannot move it other than lifting the rear end off the ground
does anyone know if that 1989 has a nutural gear to be pushed
sure help if i can find that out
thank you all that reading this

Have a b5200 need to replace glow plugs and glow plug incator new key swith belive key turns to left to make glow plugs to work

Test

Hi EVEL (A Bike Guy, right??) You said " Oh, BTW, me thinks that was Sean Diddy Combs you quoted "
Jeezum Crow (A Vermontism) you must be a LOT younger than me, quoting guys that are still in Jail...
Regards, Terry

Greetings all,
New member, new 2380 with LP Grapple....3 hrs in, the jaws stopped opening/closing, everything else fine. looked and saw 4 wires sticking out below the joystick button....they must have been jerked out, tho not real sure how it happened.

I can see where 2 of the wire go in a quik connect, but cannot see where the other 2 wires were connected....need a diagram, manual not present, cannot find diagram online...anybody seen this or that wiring diagram for grapple?


i'm offically bleeding orange now!

cheers!

Welcome Brother

Alan
To send you a manual I need your email address
What model is your machine as I only have a limited number of models
My offer to you is this as it has been to all others looking for WSM's.
Send me your email address

I will sent to your email address a Jumpshare link to download the WSM.
Once you have it downloaded, if you agree it is as stated, you will agree to upgrade your forum membership to any of the paying ones.
These funds help keep the forum up for everyone's benefit. Nothing comes to me!!!
If you do not see the link in your email IN box check your JUNK folder.
If you are having tough times financially, tell me and I will make an exception

Dave

I just got a 2005 Kubota BX1500, 1 day ago. It ran great. I love the tractor. Today it will not start, no power or lights, everything is dead. The battery and fuses are okay. Does anyone know what the problem is? Thanks

We are looking for the bucket tilt lever for our L285 tractor. Ours is bent and cracked, I'm afraid if we try to straighten it it will break.

I would be interested and figure out something for shipping/getting if they are the correct size?

Not sure if I'm posting this right. I have a kubota l2800. It's a hst. I was bushhoging a few weeks ago and thought I hit a stump on my hst filter because it's was leaking lol. I got new filter from dealer and it is leaking in same way. It's like it's pushing the seal out of the filter. So I bought a new filter mount and put it on. It ran fine for about 20 minutes and the seal blew out again. I've searched the web for a similar problem but can't find anything. Would love some info if anyone can help. Thanks

Eric
I have a library of WSM's including the one for your machine.

Re WSM
My offer to you is this as it has been to all others looking for WSM's.
Send me your email address

I will sent to your email address a Jumpshare link to download the L3901 WSM.
Once you have it downloaded, if you agree it is as stated, you will agree to upgrade your forum membership to any of the paying ones.
These funds help keep the forum up for everyone's benefit. Nothing comes to me!!!
If you do not see the link in your email IN box check your JUNK folder.
If you are having tough times financially, tell me and I will make an exception

Dave

issue with my 3 Point Hitch. With a load on it it will not pick up. With no attachment it does. The main difference in this thread is I do not have a Front end loader it is just a tractor. Any suggestions?

What's new with you Good Sir?
The ballast box is great. I've used it for a tool carrier more than a counterbalance so far.
I've been cleaning up some of the junk from my parking area. I had a 5' belly mower that I had stripped of parts. I have another 5' belly mower that is complete but needs a new oil seal on the bottom of the gearbox main shaft. I have the seal, just not installed.
I upgraded to a 6' mower when I took the 5' deck off to change the oil seal!!!!! LOL It is amazing how much more ground I can cover with that 6' deck. The gauge wheels (on all four corners) make it easier to get the max width when mowing.
Thanks again for the ballast box. I made a stand to set it on and it's a "peach".
Ye Ole Caterpillar Cowboy