New profile posts

issue with my 3 Point Hitch. With a load on it it will not pick up. With no attachment it does. The main difference in this thread is I do not have a Front end loader it is just a tractor. Any suggestions?
What's new with you Good Sir?
The ballast box is great. I've used it for a tool carrier more than a counterbalance so far.
I've been cleaning up some of the junk from my parking area. I had a 5' belly mower that I had stripped of parts. I have another 5' belly mower that is complete but needs a new oil seal on the bottom of the gearbox main shaft. I have the seal, just not installed.
I upgraded to a 6' mower when I took the 5' deck off to change the oil seal!!!!! LOL It is amazing how much more ground I can cover with that 6' deck. The gauge wheels (on all four corners) make it easier to get the max width when mowing.
Thanks again for the ballast box. I made a stand to set it on and it's a "peach".
Ye Ole Caterpillar Cowboy
R
rc51stierhoff
Hey buddy. I hope you are doing good. I am not sure I ever see many posts on the regular threads. I wondered if the box is working out? I am glad you are getting use out of it. I carry tools in mine too. I built a new one and post the thread but I don’t remember where it is.
R
rc51stierhoff
Oh here it is…see what you think.

Hello TKDavison,
Today I noticed a steady leak from my BX23s that seems to be similar or the same as what you had posted about back in 2020. As soon as the tractor is started, hydraulic fluid is pouring out from that same area. But the post does not say what the problem and solution ended up to be. Can you give me any information on what your issue turned out to be and how it was fixed?
Thanks for any help!
Post some photos of the top of your battery and also where the ground cable connects to the frame
Dave
2012 M6040. Im having issues with it stalling and it seems to be getting air in the injector. It all started when the 1/4" return fuel line popped off going back into the fuel tank. I put it back on. I didnt run it out of fuel or nothing. It would stall and starve for fuel at 2000 RPM and eventually die. I drained the fuel separator and have changed the fuel filter twice. I sucked the fuel out and then changed the fuel filter the 2nd time. I notice the fuel in the water separator cup gets about half way down at times. I have had to bleed the injector to get it back going. I did confirm that my O-ring was on my separator. Got any suggestions?
Hkb82
Hkb82
Well, it definitely sounds like you have a leak or air getting into the system before the separator maybe the fuel line that popped off on you is sucking air in still?
Hey Y'all! I followed your advise and passed on the BX2200 with high hours.
I found a BX2360 with 620 hrs for the right price and I am so happy!
It is such a delight to use.
I know this is just the beginning of my BX journey and can't wait to learn more!
Again, 'Thank You to everyone who took the time to help!'
Hey Ron,

I see you have a b8200. Wonder if I can ask you a question?


I just picked one up about 2 weeks ago, I'm loving it so far- been doing some grading, moving materials, moving with pto mower, working great, only got like 450 hrs on it.


I can't get it into the highest or maybe the lowest range.


The range selector is hitting something. I posted pics here:


https://www.orangetractortalks.com/forums/threads/issue-with-range-shift-on-b8200.69846/#post-731765


Just curious what the range selector lever looks like on yours and if those two levers are connected?

Thanks in advance man,


Sean
D
DustyRusty
You will never get a reply unless you post your question to the members of the forums. Click on the word "Forums" in the black banner above. Pice the forum that you want to make a post to, and then submit it. Most of our members never read the profile posts.
My L 245 DT Kabota will not idle do you know why. Please respond if you know or can direct me to someone wwh might know.
D
DustyRusty
You will never get a reply unless you post your question to the forums.
I’m buying a new Kubota, I had the dealership bring a M6060 & itwill fit in my shop door top opening of 101. 5/8" with 1.5" of spare room i want the M7060 model but is bit higher with slightly bigger tires, Does anyone know the exact height of a M7060 to top roof cab??
The m6060 is 99.75” tall

2nd. What is the lowest tire psi i can use in it still & fit under doorway?
i prefer low pressure anyway, tires are 16.9 x 30 on m7060
thanks in advance
D
DustyRusty
You will never get a reply till you post your question in the forums. Most members don't use the profile posts and lots of members don't even know that they exist.
Did you end up removing the carbon canister from your system? I'm struggling with my 500 not cranking when its hot and sits in the sun. Initial start under the shed it fires right up but after that if you dont cycle key twice most of the time it will not start. I've watched some videos of removing this off a CHMOTO 4 wheeler, same idea just different setup. Dont really know which hoses to plug and ones the leave open to vent.

Thanks
D
DustyRusty
You will never get a reply unless you post your question to the members of the forums. Click on the word "Forums" in the black banner above. Pice the forum that you want to make a post to, and then submit it. Most of our members never read the profile posts.
I purchased a kubota l2050. The lower lift arms are missing. Could you tell me how long they are?
Good morning Lance...any chance you might have a spare Z751A diesel engine laying around? I'm looking to swap out my old one.

Thank you in advance,
Dick
New to Team Orange, Recent retiree using my new to me (1400 hrs) L4600 to develop and maintain our 12 acres in East TN.
I hated mowing as a kid; but turning tall grass into clippings in 6-foot swaths is pretty relaxing.
WSM B2320
Re WSM
My offer to you is this as it has been to all others looking for WSM's.
Send me your email address

I will sent to your email address a Jumpshare link to download the B2320 WSM.
Once you have it downloaded, if you agree it is as stated, you will agree to upgrade your forum membership to any of the paying ones.
These funds help keep the forum up for everyone's benefit. Nothing comes to me!!!
If you do not see the link in your email IN box check your JUNK folder.
If you are having tough times financially, tell me and I will make an exception

Dave
MaineSpring
MaineSpring
Thank you, sir! Your terms are reasonable rather ingenious.

I'm in the process of trying to decide whether to part out or repair my 2320. If I part it out a WSM really won't profit much, so I'm going to hold off until I know for sure how things are going to shape up.

Regards, Jason
I am in NW Montana. I'm moving this fall into a rural area with heavy timber and heavy snow. I've inherited my childhood B7200 hst 4wd and need to find an attachment for snow removal. I've been reading all week about the debate between front and rear mount and I believe I want the front mount based on the length and curves in the driveway. There is a GF 5225 for sale near by, does anyone know if this will fit? Other recommendations?
I used this tractor extensively when it was new back in Indiana in the 80s and 90's but haven't touched it since 92, but excited to get it out here and be back on it.