Search results

Hello sorry I took took so long to get back an let you know I got it fixed .it was the lift cylinders I rebuilt them an works perfect now the packing seals bad one cylinder rubbers was hard an was the one that kinda worked the other was in little pieces. I wanted the thank you for your time an...

OK I've been working on it an went an used for hr or so an the more I used it the better it work. I still can't raise arms at idle but 1k rpms it will raise an it'll pick up bucket load of gravel an when the arms get about 50% up it'll speed up to normal speed IL check the hoses configuration...

After I pulled 3pt valve out it worked kinda an then started to fall off agin and after I pulled inlet an return lines to pump an put back on it started to work agin kinda I'm about to switch return to pb port an IL let you know what happens thanx agin man your wisdom is appreciated

I've kinda done that IL have to hook back up to the p port agin but I took the 3pt control valve out it sitting on work bench.rite now it just returns through the 3pt hole because that's where it screws in at .so it should just be the FEL hooked up at the moment I also notice the driver side...

The red plugs is where I plumed into an that copied how the original control valve was plumbed

OK IL post them tomorrow when I get around thanx agin for your time .this evening I went out an messed with it agin I unhooked the pump line from pump an blew into it I could hear bubbling in Trans Soni hooked back up an then unhooked the return line to Trans an ran a tig welding rod through it...

Yes it is with hoses an no quick connect . The control valve has p on it I have tht going to hydraulic pump an other side has t an there are 2 ports there an that goes back to top of transaxle under seat . I've tried both t ports same symptoms. I've been playing with it today an it's almost not...

I've only got the FEL hook up rite now an it has brand new 4way directional control valve an all new connections and the bucket cylinders that's wat I've already replaced other then fluid an filter . When it started slowing down yesterday if I got load on it it would come alive some times an...

Hello agin it only wanted to work if I held the 3pt lever an make the 3pt raise the FEL didn't work if I tried to lower the 3pt. An it now it works but not alot of lift capacity with the FEL I think I got an air pocket an can't get it out . It all worked almost normal speed at first an the more...

Gd morning OK I was able to get my FEL going .the problem was the 3pt control valve . I couldn't get it to work properly so I just took it out so I can get some work done an will put the new one in Saturday or Monday whenever it gets here . I wanted to thank everyone who helped me with this...

OK thanx for your wisdom I'm new to the hydraulic game IL try to adjust lever setting first an if it don't fix IL tear back into Transaxle an try to adjust the control valve adjustment an hopefully one of them will fix it if not IL buy new one thanx agin for your time IL repost tonite let...

Thanx that makes perfect since to me now an the loader does work normal when 3pt is intermediate position . The 3pt valve has adjustable pressure bolt an lock nut if I loosen it a Lil will that help that spool return to neutral or do I need to just buy a new one an be done with the 45yr old one...

Thanx Dan for the reply yes when I pull the 3pt lever just far enough to make the 3pt just barely start to move up the FEL will work fine . Any time I engage 3pt to raise, the FEL works fine but I will just barely engage lever so I don't have to raise an lower the 3pt abunch of times. An this...

I think it does it returns to center when released .is there a way to adjust that to center it better .it's just strange to me how it all worked fine until I changed hydraulic fluid that's what stumped me I thought air at first until other day I found that if I engage 3point just a tad the FEL...

Thank you for your thoughts I have pulled that control valve out of transaxle under seat an found there was 2 rubber orings that was bad I replaced them an cleaned the spool rod an the 2 detent check balls the big one has a adjustable bolt the other does not just tighten all way in .that small...

I'm sorry I jump the gun didn't read all of it your Lil to far for thanx agin sorry but that

Hello can I ask what state your in to know if it's worth the drive for me

Hello I have a zen-noh 1500 I have been working on it for Lmost a year now trying to get it all going rite. A few weeks ago I decided to change all fluids an new filters an screen for hydraulics . B4 I did this everything worked just slow . After I did this my FEL would not raise up it curls an...