Search results

Thanks Dan! I'm an idiot... The mechanic only changed one set of the three disconnects. When I reinstalled the loader one line (return maybe?) wasn't fully seated due to dirt. After cleaning both sides and ensuring it was fully seated, everything worked. Thanks again for helping get it sorted.

Thanks for the quick replies... A little more clarification in case I omitted something crucial. Before disconnecting the the loader to have the tractor serviced, everything worked as it should although the lever movement for roll back was finicky. When moving the lever to the left there was a...

Hey Everybody! So, I'm back with another weird issue... I've already searched the internet and this forum for answers. After a major servicing (including hydraulic flushing and filter change) of my BX2200 from my local Kubota dealer, I re-attached the loader (LA211) and immediately blew out a...

Hey guys! Final update for this thread. Took the tractor to the dealer. Mechanic said he found nothing wrong, but, as a matter of habit, he changed both fuel filters and added some fresh diesel. Then primed the injectors and it fired right up. Draw your own conclusions because I got nothing...

That may be true, but I wouldn’t classify my Kubota engine as “modern” since it’s all mechanical without an ECU. Either Way, it didn’t cause any damage, but thanks for the warning.

I’m at the point that dealer service may be the most prudent next step. Unless someone here can help me have a “eureka” moment. I do appreciate all the helpful advice offered throughout this thread.

Yeah, I’m not an expert on engines, but, when used properly, can help diagnose a non-starting issue. Previously, I used it sparingly directly into the intake manifold while cranking, and the motor chugged a bit. I tried the same thing, but with a mist of diesel from a spray bottle. It didn’t...

The pump is mechanical, and requires a lot of parts to be removed. I would not try starting the engine in this state unless I knew for sure it was safe.

My injectors are mechanical. In the video I attached to a previous post, you can see I let the glow plugs "pre-heat" for about 15-20 seconds before starting. During that time they were getting 10-11 volts.

Yes, I had the solenoid physically removed and tried starting, but there was no change. Also, watched the plunger while doing this and it worked correctly.

correct

Correct. It is low pressure from tank to injection pump. Also, correct. The pump and injectors are mechanical. I highly doubt it's an electrical issue now because there's only 3 electrical things that need to work: (1) Fuel pump (2) Starter (3) Glow plugs. If you watch this video you can see...

I just checked everything again. I disconnected the fuel return line. When the key is turned to ACC the fuel pump runs and fuel comes out of the injection pump return line outlet. Return line reconnected. Removed stop solenoid. Verified it functions correctly. Re-installed. Removed retaining...

Update #5 Rebuilt injection pump, injectors, cleaned hard fuel lines, new overflow return piping, and new rubber fuel lines. Everything installed and torqued to WSM specs. No change. Short video of attempt to start

UPDATE #4 I called oregonfuelinjection but they quoted new part prices to rebuild my pump and injectors. ($700+ for pump and $100/ea injector) I found this guy out of WV hickoryridge61 that did a good job with fast turn around. I've got almost everything put back together, and will post the...

Thanks for the help diagnosing my tractor issue. I truly appreciate it. I plan to remove the pump tomorrow, but will check the hard lines for blockages. As for the injectors, I don’t want to spend the exorbitant OEM price, but it’s difficult to filter quality from junk aftermarket ones. Any...

Is the injection pump serviceable? Or is it only replaceable? (nevermind) I just checked Ebay and found rebuild kits. So, I guess the question is... Has anyone rebuilt one? Is it something a "hobbyist" can do or better left to a pro?

What I'm calling "start position" for the key is when the starter engages and cranks the engine. I've already verified my stop solenoid functions properly. I've made no adjustments to the part highlighted. It is as it was when the tractor ran. I have tried adjusting the manual throttle lever...