Search results

It is, but when pushing snow it flows out the sides. The pusher collects it better with less side spillage. Plus its faster. Ever watch one of the front end loaders do parking lot with one on? Just imagine it doing 1/2 the width with bucket only....

The 60” backdrag is bolted on. It was about $150 option I think, got mine beginning of 2022….

Should get the poly scraper bar for it, unless they don't offer it for the 48" size. One thing I don't like about the Land Pride models is the back drag feature is steel edge,not a poly one....

Alrighty, it seems I should have more than enough pressure. The only thing I can't remember when I checked it last year before I dropped it off at dealer was which fitting on the manifold I connected the gauge to- if it was the first or second one closest to operator. Instructions said first...

Do you have any hydraulic hose dealers near you? Take the old hoses and ends with you and tell them what you want to go to....I'm lucky and have one 6 miles from me. Even if you have a dealer they probably can get you set up with what you want, I'm sure they've had people wanting to delete that...

They replaced loader, but I don't think they replaced the loader side frames(saddles), as I didn't get any saddles when I picked up the old loader. I believe that's where my problems lie, I shall soon see....

They supposedly shimmed it last year when I had it there. I need to check it again...

Yep. Another thread here about bucket meeting ground unevenly. KTAC did SOC on the old loader, I bought it back. After using it a couple times with new loader bucket uneven again, so I put old loader back on. If I keep old loader I’ll swap grapple lines over to that one and use for grapple work...

The hoses and fittings are on the new loader, I have the old loader on now. But weird thing is, I was able to pick up 11 pallets today with it no problem. Only thing that changed was how hot it was outside- when I could hardly lift pallets last week it was in the 90's and humid. Today was low...

Checked fluid and added after install. Gonna double check my lines from power beyond and loader valve, I had a new ne made (48") and had the other one cut to 54" and new fitting. The hoses Summit sends with kit are way too long-they sent 2-60" lines. I did video of how I installed it after it...

Hi folks, a question. I installed a Summit third function kit on my BX2380 back in March, then dealer had it a couple months, and haven’t used it much since, just been using the bucket moving dirt/gravel a couple times. I used forks a couple times to move a snowblower attachment for another...

Experience using loader, comes with time. Just need to leave bucket level on ground when you go to pick end of pile up and speed a little into it, Just make sure nothing important is on other side of pile:ROFLMAO:

Oof. Is this how the hoses are run with the Kubota kit? What a piss poor setup if it is. Those hoses are ripe for a stick /branch/other object getting caught in them and ripping them down and off. What is it with dealers lately that are doing half ass checks on equipment before delivering it to...

I didn’t see weight rating on tire…

Thank you. Guess I’ll take tube back to Harbor Freight.

They are the ones that Kubota puts on, so 780# like yours. The same ones on ebay are 780#

If it’s dry, the R14’s are fine. It’s in the spring and fall when lawn is soft that the R14’s are not kind to..

What size tubes? Will the 18x8.5/9.5x8 work before I take tire off?

Hi folks! Used my BX2380 today and noticed front tire was almost flat. These are the 18x8.5x10 Grass Master turf tires. I had them at 20psi( max on sidewall listed is 22psi) to move some dirt last week, and also last fall moved quite a bit. I only used the turfs because the R14T tires would have...

2” is really close to rear wheels on 60” deck on my 2380. As previous post mentioned, measure from outside of tire to edge of caster on both sides. Also keep in mind you may not be able to turn the rear casters for deck removal if you get spacers. Biffs equipment has video on YouTube installing...