Search results

I have a set of Tap and Dies. If I don't know the pitch I grab the tap or die and measure it. Bonus is I don't need another tool or a bunch of bolts hanging around.

Yup mine did the same thing, it took me awhile to figure out I was sliding forward in the seat just a little bit. I first thought it was low on fuel, so I filled it. When it kept happing I noticed my slide.

I replaced them yesterday. They only had 300+ miles on them, but most of those miles where lees then 50 yards at a time.

Well I got the answer. "Hello, Thank you for your inquiry. I do apologize, they are not available aftermarket as of yet, Kubota have not released the part to be sold aftermarket. They are only available through Kubota dealerships. Lela Martin Lead Technical Service Rep – Aftermarket...

I went to the NGK web site to look for them or there replacement. They didn't list any, so I went to contact us for product support, and asked what the replacement number was. I doubt they will respond, but I hope they do because these have been discontinued. I will give it to the end of the...

Thanks for the Kubota number. $20 bucks for one spark plug seems way too steep. I guess they have a really high markup on these.

NGK MR7J 9. This is one of the plugs I pulled out. I guess I am off to the dealer tomorrow to figure out what the replacement is.

Thanks all. I will pull a plug this week, and post a picture. If the only place to get them is the dealer then I guess I will be visiting my dealer by the weekend.

I did a search but couldn't find an answer. I have a 2018 XG850 I bought new in 2020. It is time to change the plugs. Before I go to the dealer are there any aftermarket ones that will work? Thanks Mike

Well my battery is staring to go bad on my XG850. It is a Group 26 with 560 CA. I checked all the Auto parts places and the tractor places in town, and no one has one. I kept finding the group 26 with 540CA. One of the auto places said if the battery was made before 2019 they changed the...

Bar oil for chain saws. I use old engine oil a lot for bar oil, why wouldn't new (old) oil not work for the same thing? That is how I would get rid of it at least. Maybe put it on Facebook Marketplace for free must pick up. The other thing I used to do with old engine oil was, I had a coffee...

Thank you. It doesn't look that bad.

Howdy. I have had my Sidekick for 3 years now and have never checked the CVT belt. I looked in the manual and it says check it every 100 hours. Well I am over that by two. I was looking at Youtube and couldn't find a video on how to check it or change it. Anybody have a video of this, or a...

I use my Dewalt impact wrench on the bolt side, and hold the head side with a regular wrench. Pull the trigger and it gets tight. I take mine on and off depending on what material I am moving. Also if I need a smoother back blade job. I have never had the nuts back off or get lose.

I am sure this question is in the wrong forum, but I am not sure which forum to use for it. My yard is pretty bumpy small holes all over it in some places. I have read here a few times to use Peat to fill the holes in. If I get a few bags of peat moss to use, do I just spread it over the...

I will be looking into a standalone unit, the person that did my stumps said he might be willing to sell the grinder and trailer. I might give him a call and ask if I could go out a few time with him to learn how to use it correctly and maybe buy it. After watching a few too many YouTube...

The Titan I am looking at uses the PTO to drive the grinder, and the hydraulics to move it back and forth. It states it will work on anything form 20hp to 60hp cat 1 3 point. I am just not sure if the backhoes hydraulics are what is used to power the cylinders to swing it. 3 Point woodchipper

Ok I really think I should know the answer, but I don't know for sure. I have a BX23S with the backhoe. I am thinking I want to get a stump grinder to make a little side money and clean up a few stumps in my yard. I have been digging them out, and I am wondering if a stump grinder would...

I am almost done with all my projects around my property that is why the chipper went away. I used it for 3 years and don't see a need for it anymore. Depending on how much longer my project goes on, I may just sell the tractor also. If I keep it for some reason I might get a set of forks...

I sold my wood chipper, and had to figure out how to move it without taken off the back hoe, and no pallet forks. I think worked out nicely.