Search results

I have the pipe connecting to this part broken. It appears to be some hydaulic oil filter? But I can't find or identify the part in the parts manual. Hope somebody can help me identify it? The first picture is from the service manual, identifying where the part is located: on the right hand...

Just purchased this 50" flail mower for my b6000. It needs some work to get back to life. Hope someone here can give me a hand: 1) What's the belt part number or length? The previous owner has no idea what the size is. I guess I could figure it out by trial and error but hope someone knows this...

Hi there, A b6000 owner wants to get a brush hog. But I found out that I will need a reverse direction overrunning clutch (coupler) to run it. Anybody let me know where I could get such a thing? Thanks!

Back ground on my B6000: 1) it has a mid mount PTO. One of the reasons I am thinking of a MMM 2) it has a big loader frame goes from front right to the rear wheel hubs 3) it has a backhoe that I prefer not to remove for a brush hog type mower if possible. It acts as a weight and hook up...

I am looking for the following parts for a Kubota B6000: 1) u-joint3 66591-56413 (66591-56316, 66591-56310?) 2) u-joint 66591-56320 (66591-56315) Please let me know if you have these. Thanks!

The boom cylinder of my 619B backhoe (on a B6000) is leaking. The manual indicates the part number for the rebuild kit is 1118. I have searched everywhere to no avail. Maybe they have changed the part number? Anybody has this info and where to get it? Thanks!

Found the lengths from the manual but there is no mention of fitting type and size. I won't be able to get to my tractor for a while and want to get the hose or hoses before I get there next time. I believe it's the boom up hose that has busted. Also, anybody knows where to get the o-ring kit...

The detent balls and spring on my B219 control valve rusted real bad. I could not find replacement and want to make it work somehow. The rust balls has a dia of ~3.8mm. Nowhere to see the spring. So I bought some 4mm stainless balls and plan to drill the hole to suit if needed. The only thing...

I have put the 619B backhoe on my B6000 over the weekend. The dipper arm goes up very slow and goes down very fast, like throwing a rock and there is nothing holding it . So it hammer the ground hard if I did not stop it within one second. I did make all the cylinder go through a few full...

The ROPS is part# B1060, which is availabel for $129 puls shipping. But my dealer said it also requires B1401 ROPS adapting kit. This kit is not avaliabel until fall. He said nobody at Kubota knows what the adapter kit is for and what's in it. My question is first what's in the kit. Can it be...

It gets very good reviews. Will this work on a small kubota, like my B6000? It has a 40" bucket and the smallest rachet rake is 52". I am thinking to use it clear brush mostly. Has anybody with a small tractor/loader used it? Any feedback?

on my newly acquired B6000, when I put on the backhoe hydraulic pump on the rear PTO, it vibrates a lot. I found out the PTO shaft is bent by ~1-2mm at the tail end. I am toying the idea of using a PTO adapter and some large metal pipe to bend it back with it right on the tractor. Will the...

I have removed the first shaft assembly to replace a bad bearing. But could not disassemble the assembly. I have tried to knock the front of the shaft real hard with a piece of wood and it would not budge. I don't want to damage it so need some advice. Shall I use some heat or a gear puller...

Just bought this B6000D with the factory loader and backhoe. I am going haul it back this weekend and start to fix the "transmission problem". It was listed by the dealer as "as is" and "requiring transmission repair". I have never been on a tractor before checking out this tractor. I have run...