Search results

I have conditioned myself that any and every time my butt hits the seat I give the brake pedal a kick........ have done that for years now....

I also have run into this problem....... I use the control lock much more now.....it's easy to forget though.

see this from Kens Bolt on Grab Hooks https://youtu.be/NyoXtNS1qA0

When I had a B2400 I had issues with a line that runs from the back to the front along the right side of the tractor. The line originates from the area under the seat on the right side and there is a banjo fitting that would leak. I replaced mine twice. Check that.

The axle kit is 1 part# for the complete kit which includes the axle housing and all related and needed parts to fix the leaking pivot bearing issues. The new kit has a completely redesigned and improved pivot system. Call your dealer, don't try to find a bunch of parts you don't need on...

I will try to locate the P/N but if you contact your dealer with your serial number he should be able to look it up. Make sure you advise if you have bi-speed steering or not.

The arrows point to the transport tabs.......The front lift linkage is not installed correctly in the photo...... both pins should be in the front brackets as to from a fulcrum to lift the front of the deck......

Tap out the blank covers (they use a little glue to secure them at the factory) and these go right in without modification. Just try to keep water out of them. Search Amazon for this: NTE Electronics 54-645-A Round Hole Illuminated Rocker Switch, Square Bezel, SPST Circuit, ON-None-Off Action...

Here ya go Mainetractorguy....... I found this near Kalamzoo Mi. https://kalamazoo.craigslist.org/grd/d/kendall-kubota-front-blade-controller/6982033418.html Road trip!

I was fortunate enough to locate and purchase a used Kubota B2019 Front Blade with hydraulic lift/angle and down pressure for my B2400. I fabricated a mount for a valve and bought a 2 spool valve on Ebay. I used it for years and I just traded in the B2400 and now have a B2650, I have modified...

I run a 54" Land Pride box for my B2650 rops tractor. I already had it for use with my old B2400. With a substantial amount of dirt collected in the box it will stop the B2650 due to wheel spin even with R4s and rear tires loaded. It does cover the tire tracks but just barely. A 60" will...

I have the exact same set up, I just removed the 2 90 degree fittings where the hoses attach to the grapple and connected the hoses straight to the grapple fittings. That corrected the pinch and rub issues for me.

I would also change the fluid with some new UDT since he could smell the oil, being so hot as to smell it I would dump it and put in fresh to protect the pump and hydro.

Disconnect the quick couplers and test leak down, if it still leaks down with QCs disconnected then you can assume it is cylinder packings leaking.

The bi-speed box stays with the axle, just disconnect the actuating cable from the arm. You can remove the bi-speed gearbox from the axle after it is off the tractor.

I had the same issue on my B2400 and 1st I tried replacing the pivot ends front and rear (with new O-rings) lasted a few months before leaking again. If you have more than a small amount of wear on the bearing surfaces on the axle housing itself it will leak again. Fast forward to last fall: I...

I had the same issue on my B2400 and 1st I tried replacing the pivot ends front and rear (with new O-rings) lasted a few months before leaking again. If you have more than a small amount of wear on the bearing surfaces on the axle housing itself it will leak again. Fast forward to last fall...

Another avenue to consider is adding a starting improvement relay. I just put this easy to install kit on my B series and wow what a difference in cold and warm starting!!!! It is a John Deere part but trust me it is worth every penny! The starter will energize immediately and spins the...