Search results

Few more adjustments... T1600 mower Modified RC44 deck from a G4200 relocated rear mounts from a junk RC44LT Modified catcher from a T1400 with Cub Cadet bags (The old bags were toast) I have to come up with a longer discharge tube and adapt the front clip for a hold on the deck but so far so...

I couldn't find a place to post about odd ball equipment so here we go. What I have is a Chinese generator with a 186FA 418 diesel engine. When I first got it the generator head was inop and I replaced it but doing so i had to install a different crankshaft to match the replacement gen assy I...

Just acquired another T1600 and this one is minty fresh. Just over 350 hrs and supper clean. The brakes were stuck but bow all good. Super nice. The seat is really the only thing that is worn out on the top.

Looking at a Chinese Lenar LE204D. 4 wheel drive 3 cylinder diesel @20hp. I know nothing about these compact tractors other than the company went under and they can overheat. The one that is being offered to me has no FEL and has a 4 foot rotary cutter. Seller is asking $2000. Any idea if it's...

Anyone have a coupon code for Steiner? The Cub 154 needs a new pressure plate. Thanks all

New to me International Harvester Cub 154 Lo-Boy. Clutch died but it came with a new one in a box. Hadn't started it yet because to PO took some of it apart. Running wise it looks like a complete tractor minus the deck. It's a 3 speed 4 cylinder gas with I think a whopping 17 horse power. Rear...

Looking for one 13.6-28 R1 tire in GA or a link to the thread where everyone was talking about recommendations for new ones. Thanks

So, what I have now to add to the collection is a Ford 2810. I know it's a Ford but is a new to me project. I don't know much about it other than it has set not running for at least 3 years, 3 flat tires, and a possible electrical issue. It comes with a bush hog, bottom plow, and finish mower...

Not sure what kind of cultivator planter thing I rescued today out of a old pond. What is it? I know it's heavy.

I've been trying to figure out a boom pole for it and settled for a truck bed lift. With a support I got an engine out of a car and into a trailer (480 lbs). The car was inaccessible to a cherry picker. I've used it without a support for things under a hundred lbs. I'm only using this in the...

Well, I got another old project that I can't find parts for. It's a Toro 11/38 model 57365. I hadn't got it running yet because I have to stop at the clutch. I can not find any replacement parts for it so I'm trying to source friction material to make my own clutch pad. Any ideas for you all are...

I have three old pieces of David Bradley implements. Disc harrow, adjustable foot plow, and lay over plow. Do these have any collectable value, yard art, or should I go ahead and clean them up and modify them for a sleeve hitch?

Took me long enough to start this project but now it's about finished. The goal was to make all the Craftsman parts work with as little as possible modifications to those parts while keeping the deck on too. Just use the same geometry and install in different positions. Works great so far now i...

Long shot but does anyone have Kubota G4200 through G6200 deck parts available. I need drag links, gauge wheels, and a gear box. Parts from G1800 and G1900 decks will work too for what I need. Thanks all for your help. Dan Can't break the bank so please reasonably priced/ serviceable parts...

The last G5200 I acquired had a receiver on it that I hadn't seen before. I took some pictures of it to show it off. What do you all think? I have it propped up off the floor so it's easier to see. Just an odd shaped thing.

Not new to orange but new here. I have a T1600, G4200 gear, G4200 HST, and a G4200 HST. 3 out 4 have decks and all run good with varying degrees of rust and natural patina. I only have only mower with a deck that just brings hate and discontent and that I'm definitely going to bug someone...