Recent content by rlcotter

I am also on the Ryobi platform, and it only made sense to go with the Ryobi grease gun. Zero complaints, other than I should have bought it sooner. Much easier/faster to do the job = doing it more often. I also have the lock-n-lube. No regrets what so ever.

I also have the original and no regrets at all. It has made this chore a more pleasant experience.

Hello B737 Thank you for the tip. I will do that tonight. Les.

SOLD: BXPANDED Quick On Pallet/Brush Forks BX Only For Sale: I have 4 BXPANDED Quick on Pallet and Brush Forks for BX Only for sale. Located East Toronto Ontario Canada. Original Cost for 4 was $539.00 USD + Shipping. All 4 for $260.00 USD or $150.00 for two (or equivalent in Canadian...

Hi KP. I am sure that the 50 inch would be fine, but I am glad I went with the 60 inch. It seems size appropriate for the BX. It met my expectations and I am very pleased to not be dragging around the one with the cement blocks on that you can't reach the lift for the wheels and can't back up...

I went all out and bought one of those Harbor Freight $9.99 battery operated pumps ($14.99 at Canadian Tire). Uses 2 D batteries. I put 2 of the 5 gallon jugs on a wheeled service cart, wheel it up along side, put the pump in the jug, other end in the tank, a wait 2 or 3 minutes to top up...

I put my 60" CMP Attachments dethatcher together today and tried it out. It worked as expected, all parts were in the box. Assembly was easy. Unfortunately, I am not a welder so I am in a position that my attachments have to be purchased. This item was not inexpensive, but the quality seems...

I purchased this one from CMPAttachments.com . It arrived late Friday afternoon and it is still in the box. https://www.youtube.com/watch?v=xfCqlvigRyM I will update once I have it assembled and tried it out. Les.

I see your point tiktok, makes sense. Everyone has there preferences. I have the backhoe, and it is one quite often, and then the back blade. So just no real need for me, but for others, like yourself it makes perfect sense.

I bought a ballast box in 2015, and I used it at the start, but found out that most attachments on the 3 pt work just as good. It sits in the corner of the garage. You need ballast for sure if you have the FEL, but I personally would not buy it again. I have attachments that I use regularly...

I was into my dealer for the same issue. I have the BX23S and there was a bulletin on this issue on their computer.

Hi SMbx. I am in Ontario and we have had temperatures in -20C range over the weekend. I was at my dealer a few days ago, and he had a fuel filter that he had removed from a BX. He told me once you have gel in the fuel filter, you can't do anything but change both fuel filters. He said they...

Hi Bigmoose. I had the bx2370 and now have the bx23S. I had the sloppy FEL on my 2370 as well. Always greased within 10 hours of operation. Didn't like it at all. My BX23S does not do that at all. 2370 with pin, 23S with SSQA. Different setup entirely, but I have to say I had the same thing...

Good morning Frozenintime, This is a unfortunately common mishap. Once you have this replaced, you should consider under armor protection that is readily available. The fan is wide open under there, with minimal protection. As mentioned above, plenty on the site regarding this situation...

That sounds like robbery to me. I bought the BX23S in April 2019 and had the dealer add the block heater before delivery. They charged $100.00 CAD installed. Good luck sorting this out. Hopefully, the dealer comes to his senses or Kubota Canada comes to the table. Les.