PoTreeBoy's latest activity

  • P
    PoTreeBoy reacted to chim's post in the thread motor oil l 35 with Like Like.
    Welcome aboard! I'm not familiar with the L35. Many engines have a cap that says "OIL" when viewed from one side of the tractor or...
  • P
    PoTreeBoy replied to the thread Fall Colors.
    Not that the area is known for its fall colors, but I think the west Tn/north Ms fall color is going to be brown. We're supposed to get...
  • P
    PoTreeBoy replied to the thread motor oil l 35.
    A. Plug 090 on valve cover, but you'll have to remove the hood (and sides, I think) or B, plug 360 on the left (driver's) side of the...
    • 1000006500.png
    • 1000006501.png
  • P
    PoTreeBoy replied to the thread Kubota L200 Rebuild.
    From your earlier post I was wondering how you'd get to the rod ends. Looks like that side panel behind the oil filter gives access for...
  • P
    PoTreeBoy replied to the thread L3400 1,200 Hrs - Transmission issues.
    I'd figure out just how low on fluid it is and fill it up. Low fluid could cause your problem.
  • P
    PoTreeBoy replied to the thread Grapple University.
    Two cylinders doesn't necessarily mean twin lids. Mine has a single lid with a cylinder at each end. It operates same as boom or dump...
  • P
    PoTreeBoy replied to the thread Bolt or bolt tip name and standard?.
    Here's what BS 4168 in the 23rd edition (1988) says. Sorry, this was before B18.3.6M, I believe. In any case, I think OP's is...
    • 1000006486.jpg
  • P
    PoTreeBoy replied to the thread Grapple University.
    The L35 loader capacity is ~1600#, I assume at the pins. The SGC1060 weighs 400#, so 1/4 of rated capacity. 1/4 of 952 is 238, the...
  • P
    PoTreeBoy replied to the thread What's cookin' boys?.
    You'd get strung up in Texas for calling that chili, but it sure looks delish to this southern boy.
  • P
    PoTreeBoy reacted to GrumpyFarmer's post in the thread Grapple University with Like Like.
    I think you got some solid advice from others above. I definitely agree that especially for smaller machine grapple can take a big bite...
  • P
    PoTreeBoy replied to the thread Grapple University.
    Hope this doesn't get too long. I started hauling the weed saplings I cut with the bucket (actually mostly on the arms above the...
  • P
    PoTreeBoy reacted to TheOldHokie's post in the thread L245Dt FEL front hydraulic pump and shaft problem with Like Like.
    My preference is chain couplers for the shaft and spin on wire mesh strainers with a bypass head for suction side use. Dan...
  • P
    PoTreeBoy replied to the thread L3400 1,200 Hrs - Transmission issues.
    With HML, it must be hydrostatic - the manual is 4x2. OP, can you verify if it's hydrostatic? Can you shift it into high with the...
  • P
    PoTreeBoy replied to the thread L245Dt FEL front hydraulic pump and shaft problem.
    I'm pretty hard-headed, so I'd try to make the existing system work. After all, a similar system works on my L35. As @North Idaho...
  • P
    PoTreeBoy reacted to Easton's post in the thread Urban Farming With the Ol' Man with Like Like.
    Thank you for reading our story. Honor certainly comes in all shapes and sizes and colloquialisms carry different tones in different...
Show older items
Top Bottom