pgrovetom's latest activity
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.Its rather tricky. The 10x1.25 hole in the head is about 3/8 but metric. So its not practical to drill a hole in a 10x1.25 bolt thats so...
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.Arduinos make it really easy. Free PC development tools and language. Free example code. Just about any board configuration you can...
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.That's one approach. That sensor cannot be adapted to the Kubota sensor threaded sensor. It also uses a non-waterproof LCD display. I've...
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.I doubt any other dash is shaped such that it would fit. I also doubt the electrical interface is exact such all the functions work.
-
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.Yes. I am looking for a gauge sensor combo that fits the Kubota M10x1.25 inch sensor but that combo is also rare. When I compared the...
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.I've scoured the Internet and its not available, new or used. Once I got inside, its pretty clean. I think I'll use plan B. Its not...
-
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.Yes, I purchased a BX25 but the motor says BX23. I'll post a picture. But I found my problem. I took the servo motor back off and found...
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.Update: So I took the dash board out and made an important discovery. The fuel and temperature arms are rotated by what appears a small...
-
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.So I took the dash board out and made an important discovery. The fuel and temperature arms are rotated by what appears a small black...
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.I want to verify the sens location having got bad info on internet searches. This is the one that appears to be the thermo sensor but I...
-
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.Here is the label "D902-E3 BX23" on top of the engine:
-
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.The top of the engine has a white label that clearly says BX23 but I purchased a BX25 with backhoe in 2008.
-
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.Ok, looks like bad sensor. I had the electrical diagram ( included here) and the gauge is connected via the harness to ignition 12V . So...
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.The needle gauge is pinned all the way to HOT with the power on or off with the sensor connected or not to lead. The sensor Ohm reading...
-
-
Ppgrovetom replied to the thread 2008 Kubota BX23 engine in BX25 Temp Gauge Stuck pinned HOT.I can't help but wonder why the fuel gauge seems normal if the dash ground is open. I suspect the thermostat has a thermistor in it...
