Menu
Articles
Forums
New posts
All threads
Latest threads
New posts
Trending threads
Trending
Search
Search forums
Search profile posts
Members
Current visitors
New profile posts
What's new
New posts
New profile posts
Latest activity
Latest threads
New media
New media comments
Classifieds
Media
New media
New comments
Search media
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Latest activity
Account upgrades
Register
Menu
GeoHorn's latest activity
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
GeoHorn
replied to the thread
B7200 running hot
.
I offer the advice to AVOID CHEMICALS. I’m 3/4’s of a century old…and I have a LOT of experience from my youth of using cooling-system...
Sep 11, 2025
GeoHorn
replied to the thread
M9540 3 pt. hitch speed control problem
.
Item 3 is mis-spelled. VICE… is a word to describe morally wrong behavior or a defect in character. (Hence the term...
Sep 11, 2025
GeoHorn
replied to the thread
L3901 - overheating after extended, heavy duty brush hogging
.
The overflow tank seems to be working properly then. As the machine heats up…the expanding coolant eventually over-pressures the...
Sep 11, 2025
GeoHorn
replied to the thread
Suspension Seat on a Zero Turn?
.
Are your tires being run at the recommended pressure? My mower had a “hard” ride….. until I reduced the tire pressure from 35 psi (as...
Sep 11, 2025
GeoHorn
replied to the thread
L4310, HST, 4x4: hazards/turn signal
.
It’s unlikely that a “flat connector” is to be grounded. It’s more likely it’s to be connected to a receptacle… or a “spare” receptacle...
Sep 11, 2025
GeoHorn
replied to the thread
Speedi-Sleeve to solve 4WD Front Axle Leak on an L3010 Bevel Gear Case
.
I suspect you are experiencing what I went thru….. a couple years ago …(I”ll try to find a link and edit this post)… My Left Front...
Sep 9, 2025
GeoHorn
replied to the thread
Front axle center pivot o ring replacement?
.
@NorthwoodsLif : What you posted makes some sense. If it were a high-wear point you’d think K would have made Mine greaseable from...
Sep 9, 2025
GeoHorn
replied to the thread
L4310, HST, 4x4: hazards/turn signal
.
Electrical Wiring is like plumbing. For water to flow (current) to the hydrant there must be pressure (Voltage) in the pipe (wire)...
Sep 9, 2025
GeoHorn
replied to the thread
The RC72-29A driveshaft clocking mystery
.
The DriveShaft is clearly Not out-of-Phase …. but your mower might need to be rotated a few degrees….if I’m understanding your post...
Sep 9, 2025
GeoHorn
replied to the thread
L3301 OIL PRESSURE
.
You’re entitled to your opinion. I’m speaking from personal experience with tractors, boats, and many vehicles. My 9N Ford tractor...
Sep 8, 2025
GeoHorn
replied to the thread
L3200 Adjustable Seat “Spring” Pressure
.
Perhaps you’ve adjusted it “all the way”…. in the Wrong Direction..? Try the mid-point.
Sep 8, 2025
GeoHorn
replied to the thread
Front axle center pivot o ring replacement?
.
It looks pretty stout…
Sep 8, 2025
GeoHorn
replied to the thread
L3301 OIL PRESSURE
.
Hokie… you yourself posted the chart which allows 7 psi at idle. My comments were not referencing Kubota WSM… they were anecdotal for...
Sep 8, 2025
GeoHorn
replied to the thread
Hydraulic fluid foaming
.
Yup.
Sep 7, 2025
GeoHorn
replied to the thread
Not Kubota Related Dwell Meter
.
I still have the one I bought in a pawn shop in 1980 for $10… combo dwell, tach, voltage, etc. I last used it on my ‘84 Volvo...
Sep 7, 2025
Top
Bottom