BonnySlope's latest activity

  • B
    BonnySlope replied to the thread What did you do to or on your Kubota today?.
    Nice looking project, and the protection against hydraulic effect of your small waterfall step. Is that a flash flood, with high run...
  • B
    BonnySlope replied to the thread What did you do to or on your Kubota today?.
    If flyidaho has got back to you yet, heres one I googled. It looks like a nifty DIY, if your handy, maybe a side shift on your forks, or...
    • Post and tree pull_Titon_DIY.PNG
  • B
    BonnySlope posted the thread Still a Howard, But Moved on in Implements & Attachments.
    After finishing with my HR10 60-inch project (625 lbs.) I decided to go on a weight diet over two hundred pounds lighter to a HR12-50...
    • Howard_HR12-50 (1).jpg
    • Howard_HR12-50 (2).jpg
    • Howard_HR12-50 (3).jpg
    • Howard_HR12-50 (4).jpg
    • Howard_HR12-50 (5).jpg
  • B
    BonnySlope replied to the thread Sprocket Nut.
    Yes, it's called Brake clean :)
  • B
    BonnySlope replied to the thread Sprocket Nut.
    Have roller chain on shelf, lots of oils and yes grease can be used when installing new gears or chain that are good for clinging to...
  • B
    BonnySlope replied to the thread Sprocket Nut.
    Thanks, in advance for pic's. I have an HR10. Like mentioned in my original post, too good to pass up. My plan is to put in a small feed...
  • B
    BonnySlope replied to the thread Sprocket Nut.
    I was thinking that, but I still need to pull sprockets. When I compare link count and length with new I'll have a better idea.
  • B
    BonnySlope replied to the thread Sprocket Nut.
    When I opened it up was oil and water. I cleaned it out with brake cleaner and when I sealed it, I filled with a quart of hydraulic oil...
  • B
    BonnySlope replied to the thread Sprocket Nut.
    I was thinking about the crowns on the sprocket, and they didn't look to bad but, I hadn't worked on roller chains and sprockets for a...
  • B
    BonnySlope replied to the thread Sprocket Nut.
    Yes, sorry for being long winded. I was planning on putting a 1/2 longer tensioner bolt so I can use jam nut. If someone can suggest how...
  • B
    BonnySlope posted the thread Sprocket Nut in Implements & Attachments.
    Hi, started a new post on my Howard HR10, got a good deal and I'm still having fun. As you can see chain has a little slack in it and...
    • chain_spocet (1).jpg
    • chain_spocet (2).jpg
  • B
    BonnySlope replied to the thread Tiller, Just couldn't pass up.
    Helo again, I have a chain question for your input. What I've read on internet about how much chain tenison is needed on different...
    • chain_spocet (1).jpg
    • chain_spocet (2).jpg
  • B
    BonnySlope replied to the thread Drilling and Tapping my ROPS for LED Lights.."OH The Madness".
    Rivnuts , insert a-thread, by different names, depending on manufacture. Oop for to mention to OP. Nice and tighty looking job. On the...
  • B
    BonnySlope replied to the thread Tiller, Just couldn't pass up.
    Well, was able to mockup tiller today and set my lower link points. Plan on fitting to tractor tomorrow to measure what size series 4...
    • 3PT_spacing-setup (2).jpg
    • 3PT_spacing-setup (1).jpg
  • B
    BonnySlope replied to the thread Tiller, Just couldn't pass up.
    great, a little more work then I believed at first. Can I ask, what level of oil in gear box. I see there's a dip stick, up to top of...
Show older items
Top Bottom