Menu
Articles
Forums
New posts
All threads
Latest threads
New posts
Trending threads
Trending
Search
Search forums
Search profile posts
Members
Current visitors
New profile posts
What's new
New posts
New profile posts
Latest activity
Latest threads
New media
New media comments
Classifieds
Media
New media
New comments
Search media
Log in
Register
Search
Search titles only
By:
Search titles only
By:
Latest activity
Account upgrades
Register
Menu
Bee-Positive's latest activity
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
B
Bee-Positive
replied to the thread
BX Series (w/ mower deck) Fuel Filter Replacement
.
If you're going to bypass a filter bypass the second one in the engine compartment. The first one will prevent anything from getting...
Sep 29, 2025
B
Bee-Positive
replied to the thread
Seeking: spreader bar / load control shaft
.
Do you really need one? As Hugo said, if you don't need a draw bar, it only prevents things from flopping around. I don't use one. If...
Sep 29, 2025
B
Bee-Positive
reacted to
Speed25's post
in the thread
Daily Chuckle
with
Like
.
Sep 29, 2025
B
Bee-Positive
reacted to
Magicman's post
in the thread
Daily Chuckle
with
Wow
.
Sep 29, 2025
B
Bee-Positive
replied to the thread
BX ROPS question
.
Did you have ag tires on the Mustangs? :LOL:
Sep 29, 2025
B
Bee-Positive
replied to the thread
BX2816 Snowblower Bare metal in the impeller housing
.
Scrape/sand off any heavy rust, apply Corroseal or similar, paint it or not, apply your favorite wax.
Sep 29, 2025
B
Bee-Positive
reacted to
Runs With Scissors's post
in the thread
BX ROPS question
with
Like
.
What about a pair of “quick-disconnect” pins instead? Cheap and easy. Not much to them really, and it makes “take down” very...
Sep 29, 2025
B
Bee-Positive
replied to the thread
BX ROPS question
.
If you can't find a used one at a decent price as suggested above I'd go the fabrication route. New ones are pricey if you can even find...
Sep 29, 2025
B
Bee-Positive
replied to the thread
oil change?
.
Runs with scissors just had to poke the hornets nest - AGAIN!! And I refuse to get into another debate on the "the best" turn signal...
Sep 29, 2025
B
Bee-Positive
replied to the thread
BX snowblower and gravel
.
You're correct, black is steel. I imagine it'd be a chore to cut/grind a slot the length of a black steel pipe and then try to fit it...
Sep 28, 2025
B
Bee-Positive
replied to the thread
BX Series (w/ mower deck) Fuel Filter Replacement
.
Awesome you got it back in service. Gas in the diesel is no bueno indeed. If your BX1870 is anything like my 1880 I just relocated the...
Sep 28, 2025
B
Bee-Positive
reacted to
bamashooter's post
in the thread
BX Series (w/ mower deck) Fuel Filter Replacement
with
Like
.
Got to the point where it wouldn't run. Took it to the Kabota dealer to have it checked out. Hoping it was only the hard to get to...
Sep 28, 2025
B
Bee-Positive
replied to the thread
oil change?
.
Full synthetic "DIESEL" engine oil is fine. The engine oil you buy for your car IS NOT the same as engine oil you get for your tractor...
Sep 28, 2025
B
Bee-Positive
replied to the thread
Over Heating
.
Just throwing darts here for obvious stuff: Air filter clean? Check the hydraulic fluid level. Do you have little plastic hydraulic...
Sep 27, 2025
B
Bee-Positive
replied to the thread
G21 MOWER: Cutting Height Adjustment Dial & Cam
.
Found this at https://www.manualslib.com/manual/438929/Kubota-G21ld-G21hd.html Doesn't say anything about the adjustment knob for...
Sep 27, 2025
Top
Bottom