L3750 3 point
- Thread starter Cards1965
- Start date
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Give me the distance from the center of the rock shaft to the center of the lift arm pins.
Also give me a couple more pictures below the axle, it looks like your missing some other parts you will need.
DO NOT OPERATE that tractor!!!
The ROPS and the fenders are NOT ATTACHED and will simply fall off if you hit a good bump.
Also give me a couple more pictures below the axle, it looks like your missing some other parts you will need.
DO NOT OPERATE that tractor!!!
The ROPS and the fenders are NOT ATTACHED and will simply fall off if you hit a good bump.
I will get this pic and measurement tomorrow. Yeah, I saw they weren’t attached when I was looking to buy. I’m currently trying to get it all back together. Thanks for the warning though, I appreciate it.
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
You need these plates (yellow), the tab and hole on the bottom (red) is critical as it needs to line up with the pin for the lower arms, they are for the sway links.
If they don't line up with the link arm pin the dimension of the sway links change as you lift it, and that's bad.
If they don't line up with the link arm pin the dimension of the sway links change as you lift it, and that's bad.
They’re actually laying right right under the PTO shaft. Why they were off, I have know idea. This was actually brought to my house on a trailer 30 miles away. I don’t know how it stayed upright.
Attachments
The measurement I’m getting is 12” from center of rock shaft to the center of the pins on the lift arms.They’re actually laying right right under the PTO shaft. Why they were off, I have know idea. This was actually brought to my house on a trailer 30 miles away. I don’t know how it stayed upright.
Attachments
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
I’m sorry, I was completely measuring in the wrong place. Thanks for the pic. I will get the correct dim in the morning. Even at 60 I’m a newbie.
North Idaho Wolfman
Moderator
Staff member
Lifetime Member
Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Arms, need 2:
Stabilizers (check chains) need 2:
OPtion: you can use 2 Rights and have adjustability on both sides:
Left lift rod:
Right Lift rod:
Top link:
You will need pins for the top link and the lift rods, easiest to get them at at local store like. Tractor supply or any farm store.
You will also need lynch pins to hold the pins and arms on.
Lift Arm fits 3-Point Hitch & Ag Hardware Lift Arms, Pins, and Bushings | eBay
All States Ag Parts Item No. 181683. Center to Center Length: 29.5".
www.ebay.com
Stabilizers (check chains) need 2:
OPtion: you can use 2 Rights and have adjustability on both sides:
Left lift rod:
E-35080-71540 LH Lift Rod for Kubota L3250DT, L3250F, L35, L3650DT, L3650DT+++ | eBay
Replaces Kubota no(s): 35080-71540, 32440-71540, 35080-71542.
www.ebay.com
Right Lift rod:
E-35070-71563 RH Lift Rod for Kubota L3450DT, L3450DT-GST, L3450DT-WET, L3450F++ | eBay
Replaces Kubota no(s): 35070-71563, 35070-71560.
www.ebay.com
Top link:
Hitch Top Link Farm Tractor Cat. Ii 16" Body Adjust 21" To 33" Overall | eBay
New Hitch Top Link Farm Tractor For Cat. Ii 16" Body Adjust 21" To 33" Overall.
www.ebay.com
You will need pins for the top link and the lift rods, easiest to get them at at local store like. Tractor supply or any farm store.
You will also need lynch pins to hold the pins and arms on.