Z421 Normal Operation --> Start jumping battery to starter --> No start at all

btganeyjr

New member

Equipment
Z421KWT, L2900
May 24, 2026
9
2
3
Arkansas
Hey all, long time listener first time caller for both my Z421 zero turn and L2900 tractor.

Anyway, we've had a Z421KWT 60" deck for 7-8 years now (Kawasaki FS730V) It has always been a workhorse for us up until roughly 30 days ago. At that point, the only way I could get it started was to jump the battery to the starter. I replaced the solenoid then, but to no avail. Anyway, we just toughed it out and started the mower that way for a month or so.

Fast forward to this weekend, and now the mower won't start at all. I am still jumping battery to starter, the engine will turn over, but the unit will not start. Figuring there's a safety switch somewhere holding it back, but I can't seem to pinpoint. I've done the following:

-Tested voltage on battery (12.5+ volts)
-Tested continuity on the solenoid (pass)
-Tested continuity on the ignition switch (pass)
-Tested continuity on the PTO switch (pass)
-Tested continuity on the brake switch (pass)
-Tested continuity on the seat switch (pass)
-Tested continuity on both arm switches (pass)


I get no noises when I engage the ignition switch, no clicks, etc. What am I missing here? Any thoughts, ideas, random shots in the dark would be much appreciated. Trying to avoid taking this thing back to the dealer for a diagnosis + repair.

Anyway, thanks in advance. Good community here, have picked up lots of good knowledge here over the years before finally setting up an account and posting.
 

Bee-Positive

Well-known member

Equipment
BX1880, Cab, FEL, Tooth Bar, MMM, QH, Ballast Box
Nov 16, 2022
1,277
1,158
113
Amsterdam, NY
Just to throw some stuff at the wall and see what sticks...
Get electrical diagram/WSM if you don't have already.
Remove, clean, reconnect ground wire(s) (battery to chassis, etc.). Very comment problem.
Load test battery, can read 12.5 volts at the battery but could be very low, 2-3 volts when trying to start.
Measure voltage at the starter while trying to start it with the key.
Look for mice damage or otherwise worn/corroded wires or connections?
 

Sidekick

Well-known member

Equipment
Kioti CK2620SE cab, RTV-X, BX2360, Z726XKW-3-60
Jul 29, 2023
1,304
1,904
113
N.Y,
My Z726 blew the main fuse a couple years ago and did the same thing. Fuseholder was under the seat with a $8.00 pink fuse blown. Replaced the fuse and all has been well since.
 

btganeyjr

New member

Equipment
Z421KWT, L2900
May 24, 2026
9
2
3
Arkansas
Thanks for the reply, much appreciated.

-Ground wires clean and snug.
-No wire damage visible anywhere
-Just tested battery and starter relay, both getting 12.5v. Starter itself getting 10.6v. Will try to get battery load tested to be safe.
-Relay isn't sending anything to the starter unless I cross the relay with a pair of pliers or jump battery straight to starter. Makes me think I'm missing something on a switch. Sighhh

Will look into getting a workshop manual.
 

btganeyjr

New member

Equipment
Z421KWT, L2900
May 24, 2026
9
2
3
Arkansas
Thanks to you as well for the reply on fuses. Visibly, all the fuses seem to be good to go. Will test them to be sure and report back.
 

btganeyjr

New member

Equipment
Z421KWT, L2900
May 24, 2026
9
2
3
Arkansas
Tested continuity on all the fuses in the box, including the spares, and all were good.

I'm really baffled. We just hit 200hrs (201.9 at moment) and have never had an issue until the last 30 days. I'm going to go gray over this one haha
 

Bee-Positive

Well-known member

Equipment
BX1880, Cab, FEL, Tooth Bar, MMM, QH, Ballast Box
Nov 16, 2022
1,277
1,158
113
Amsterdam, NY
-Relay isn't sending anything to the starter unless I cross the relay with a pair of pliers
Start relay should click audibly when key is turned and send power to starter. Should not need to jump it so I'd think it's bad. It's a cheap fix. Part number is discontinued but there's lot's of replacements out there, just do a search on the original # and they'll pop up.

Start Relay.jpeg
 

btganeyjr

New member

Equipment
Z421KWT, L2900
May 24, 2026
9
2
3
Arkansas
Start relay should click audibly when key is turned and send power to starter. Should not need to jump it so I'd think it's bad. It's a cheap fix. Part number is discontinued but there's lot's of replacements out there, just do a search on the original # and they'll pop up.

View attachment 175012

Thanks for the reply. Already swapped the starter relay/solenoid. There's something holding it back from sending power across itself and onto the starter. At same time there is something holding the motor back from starting/running. Gut tells me it's the same thing doing both (bad connection I'm missing maybe? who knows). Honestly, haven't come across something like this before for what seems like a fairly simple setup (and admitting I am no small engine mechanic or mechanic of any sort).

I've got two different ignition switches (one cheapo I just bought and the OE switch). Both test fine for continuity but it's almost like neither is working when I turn the key (no clicks, no buzz, nothing). Going to bang my head against brick wall for a bit.
 

Bee-Positive

Well-known member

Equipment
BX1880, Cab, FEL, Tooth Bar, MMM, QH, Ballast Box
Nov 16, 2022
1,277
1,158
113
Amsterdam, NY
The start relay under the fender is not the same thing as the starter relay/solenoid at the starter.
If you've already replaced the start relay under the fender then you got me stumped.
 

North Idaho Wolfman

Moderator
Staff member
Lifetime Member

Equipment
L3450DT-GST, Woods FEL, B7100 HSD, FEL, 60" SB, 743 Bobcat with V2203, and more
Jun 9, 2013
36,795
11,496
113
Sandpoint, ID
You will keep banging your head against a wall if you don't get the WSM.
 
  • Like
Reactions: 1 user

btganeyjr

New member

Equipment
Z421KWT, L2900
May 24, 2026
9
2
3
Arkansas
The start relay under the fender is not the same thing as the starter relay/solenoid at the starter.
If you've already replaced the start relay under the fender then you got me stumped.
Gotcha, I think we're on same page. Here's a pic of what I replaced. There are also a pair of relays under the seat on the right hand side. I have not replaced those, but they did show continuity.

1779643688277.png

Was just outside and maybe a better way to explain what I'm going through is jumping across the solenoid with a pair of pliers or from battery to starter is resulting in the engine turning over, but not starting despite key being turned to on position. I believe this is the same result I'd expect if the key was turned to the off position.
 

Russell King

Well-known member
Lifetime Member

Equipment
L185F, Modern Ag Competitor 4’ shredder, Rhino tiller, rear dirt scoop
Jun 17, 2012
8,102
3,191
113
Austin, Texas
If the engine is cranking over but not starting and running then you have a problem with the ignition or the air or the fuel or the compression.

Check that the air filter and intake passage is clean.

See if there is spark at the spark plugs (get a tester (or just shock yourself silly)).

See or smell if fuel is being delivered to the engine. I don’t know if it is injected or carburetor so can’t suggest how to figure that out. I would make sure fuel in tank is at least being delivered to the engine by removing the fuel line at the engine and see if fuel runs out. But don’t blow yourself up.

Get a compression tester (loan from local auto parts store).

I would guess it is something electrical that shuts the engine down (fuel or ignition) that has stopped working properly.
 
  • Like
Reactions: 1 user

Bee-Positive

Well-known member

Equipment
BX1880, Cab, FEL, Tooth Bar, MMM, QH, Ballast Box
Nov 16, 2022
1,277
1,158
113
Amsterdam, NY
I went back reread your original post and see two issues. Three if you count not having the WSM but we won't count that since you said you ordered one.

First I get no noises when I engage the ignition switch, no clicks, etc.
So get the key to spin the starter - hopefully it's the start relay. If not wait for the WSM and trace the wiring diagram until you find no volts and the problem.

Second I am still jumping battery to starter, the engine will turn over, but the unit will not start.
If it still won't start after you get the starter to spin with the key follow Russell King's advice.

Note: Many switches are in series so switch continuity may be meaningless if voltage is not getting from one switch to the next. You just end up chasing your tail. There may also be separate relay/switch combination - i.e. separate seat switch and separate seat relay. Again, the WSM wiring diagram is a must.

I hope we're not filling your head with too much, be patient, follow the voltage step by step. You may have to mow twice (high then lower) but you'll be mowing. Post the solution or more questions as needed.
 
  • Like
Reactions: 1 user

btganeyjr

New member

Equipment
Z421KWT, L2900
May 24, 2026
9
2
3
Arkansas
Shoutout to North Idaho Wolfman. I got the WSM in the mail today and had the fix within 15mins. The 30A slow blow fuse between the motor and the battery (wrapped in red tape and I had no idea was there) had blown. Quick trip to auto parts store and we are running again.

Unfortunately, rain all weekend here in Arkansas so the grass continues to grow. Alas, as my wife said when the mower cranked, that's the best sound I've heard all week. Thanks for the help everyone, much appreciated.
 
  • Like
Reactions: 1 user