Search results

Hello all, question, I swapped rear wheels so they are inside out to help give a little wider foot print, also looks better IMO. Is this ok to do? or will it put too much strain on the rear axle assemblies? Approximately 5in more span.

Hello all, my key for the ignition switch keeps falling out. Is there an after market switch assembly available? I think it has 5 terminals and I have seen them for sale but wasnt sure any would work.

Hello, just bought 2 suitcase weights for the front of my L2000DT. They are 30LBS each, which might be a tad small, but they were only $40 for pair. Is there a set of front wheel weights out there that will fit this tractor? If so where can I get them? Thanks.

Hi all, getting the final touches done on the L2000DT. I bought some new amber fender light assemblies and am installing new wire from dash/console to fenders. I would like to know where to rout the wire, below the running board or along top by the shifter? because whoever did the wiring before...

I am needing to replace the spline shaft that comes out of the side gear box for the 4WD. I am wondering if anyone cane tell me if the shaft can be removed without removing the whole gear box. The shaft is #22, and I already removed the end plate #24. The manual I have says to disassemble it...

Last weekend I was able to get the new to me tractor out for some bush hogging. I never really paid much attention but noticed sometimes the PTO didnt seem to disengage. Push the cluth in, move PTO shaft to neutral and bush hog kept spinning. I thought it was just coasting but seemed a little...

Was hoping to get some help finding a tach meter for L2000/ L225. Mine froze up and broke a brand new cable. Got the cable but everywhere says meter is discontinued. I hope this isn't the case.

Anyone know where I can get a set of hood decals? L2000DT. or maybe Kubota Diesel ? It has L225 on it but thats not what it is. Thanks

Well after 2 months of buying this L2000DT, and a lot of sweat and more money, I finally got to take it up to my hunting property and bush hog. It did fine and best of all, no leaks under it this morning. The tach did quit working and the charge/ oil lights quit working and it doesn't seem to be...

Good morning all. I have a couple questions about an L2000DT. What is the blue light for on the dash? I have an L225 shop manual with the wiring diagram in the back and most everything looks the same but it doesnt show the blue light (that I can tell). Also my tractor has a safety switch for the...

After rebuilding the steering box on this first thing after I bought it, I had started digging the money pit. I am an aircraft techinician so I always notice this and that and cant leave it alone. Since then I was finally able to drive it around the yard and the steering felt decent until it...

Im down to one last major obstacle on this L2000DT. The front axle pivot pin/bearings that allow the axle assembly to pivot over the uneven ground has severe slop. side to side, rocks up and down ect. Probably 1/2 inch of slot and seals are gone. I talked myself into an easy job, since it is...

Hello, (again) The L2000DT project is moving along. I noticed the front axle assembly has lateral slop where it mounts to the front with the pin and 2 bearings. I will eventually fix this in the future. From what I can tell it looks to be pretty simple but is there anything I need to know ? Like...

I have my rear axle out of my L2000DT and have ordered a new seal. Problem is the first seal I ordered was too small ID, so I ordered another one and it too was too small. I was using a superseded PN from an L225DT parts manual. I thought they were the same? The old seal looks ok but I...

I removed the rear axle/case on the L2000DT, yes it is not an L225DT. They painted over the data tag and put an L225 sticker on the hood. Any way I was hoping someone can tell me how to remove the bull shaft. I already removed the axle and big gear assembly.

Hello all, sorry, I know this has been covered and I even wrote the numbers down, but I cant find the numbers or my paper. Can someone let me know the PNs for the U-Joints on the Propeller Shaft for the 4WD on the L225DT? the shaft PN is 34218-44500 and not available anywhere. Thank you.

Well after purchasing this L225DT, I noticed a hydraulic leak coming from the rear axle area. Thought just a drain plug gasket so I replaced them when I changed the fluid, still leaking. Went out there today to dig a little further and found the RH rear axle case to be cracked, right behind...

Good morning all! I am ready to start getting after this tractor that I bought. Ordered quite a few parts so far, and digging this hole deeper, but am determined to have a decent tractor when Im done. Now, are these fuses still available? I have never seen anything like these. Is there an...

Hello all! I just bought a Kubota L225DT the other day. Thought it was cheap enough, but after getting it home the hole started getting deeper. I knew it would need some fixing here and there but never thought I would need a part that is nowhere to be found. The 4WD doesn't work (thought it did)...