Search results

Good advice!

If the manual is for the L1501DT, you may have to purchase one. The tractor is around 45 years old, and I do not think that many Orange Tractor Talks will have one. I saw several for sale online. Good luck with it!

Hello OrangePower, I am attaching a link to the Amazon page showing the forks that I purchased. If they work for you, they are less expensive than most others. I have already mentioned the limitations of these forks, but I like being able to break them down into three pieces for storage. They...

I have gone through all the posts, and a lot of good points have been made. Here are my thoughts for what they are worth. I have Titan brand QA forks. They don't adjust, but the forks can be removed for easy storage. The rated capacity is 2800 lbs, and the attachment weighs 95 lbs. Are they the...

I can't speak to the venting of coolant, but if the engine temperature indicator is not showing an expected increase in temperature then I would think that there are only a couple of possibilities. The indicator is malfunctioning, or the thermostat is stuck "open" and the engine is not heating...

Don't call me Sir, I was a Sergeant, I worked for a living. .............................just kidding, couldn't resist

Here is a link: https://kubota.servicemanualvault.com/Kubota-L2350-Tractor-Workshop-Manual.html

Do you want a link?

Hello onsiteservice, I could not locate a free down load, but there are several that offer a WSM download from about $10.00 to $35.00

Hello WolfrRD, Amazon offers several options. Perhaps Amazon has distribution "down under". You could check it out. https://www.amazon.com/s?k=tractor+quick+attach+adapter&crid=2QPIS3G6Q7ZZ3&sprefix=tractor+quick+attach+%2Caps%2C94&ref=nb_sb_ss_ts-doa-p_1_21 I hope that 2022 is a good year...

Hello Jeremy, Good luck with the new hooks. Not to tell you something you already know, but you have one cylinder, so the load must be evenly distributed to the extend possible. Overloading one side could ......................well you get it. Have a good 2022

Well Whitetiger, as is usual, your mechanical knowledge is right on target. Maybe the thinking was that because the fuel supply pump is creating such extremely high pressure in the rail, some sealant was required. Just a guess. My question was the difference in the pump nomenclature. is the...

Hello Ramdriver, That is roughly a 30 year old machine. I looked at Kubota books. They don't have one, and that is the only free source that I am aware of. You may have to buy one on Ebay or some other used marketplace.

Messicks offers the pump to fit his tractor as a 1J801-50500. I guess that the question is what is the significance of the part # 1J801-50501; is it in any way different? https://www.messicks.com/part/1j801-50500/assy-pump-suppl?ab=1

Hello KubotaEd, Your deck may have "lock up" capability. This holds the deck in a fixed raised position while you raise and lower the three point hitch while using rear mounted implements. I do not know if the following is applicable to you, but it is worth a look. Good luck with it, and have...

Hello 2manybikes, There are a few vendors who make this adapter. Pallet forks Inc. for one. It is even listed on Amazon. Be prepared to lose some small amount of capacity because you are pushing the load center further out front...

Welcome to the forum. You will find a number of very knowledgeable people who will glad to help with questions. Goz63 is giving you good information. Read your manual and engage and disengage the PTO as described. Slam, Bam, Thank you mam is not good PTO procedure.

Sounds like it could be a severe case of "gear lash" (the noise straight cut gears make, that decreases as RPM increases). My B2650 makes a similar sound at low RPM (not as severe), but the sound starts to disappear when the RPM's go up, and especially when the an implement is engaged and...

Thanks Skeets for the reminder. We should never forget those who served our country in big ways, small ways, or who were just there, standing by on a Sunday morning, never expecting to make the ultimate sacrifice.

Hello DougVA, welcome to the forum. Good luck with the new tractor. It will be useful in ways you can't imagine until you start using it. I would offer one bit of advice. You have 20.9 rated HP, and 17.5 rated PTO HP. That puts you on the low end of required HP for a Land Pride rotary cutter...