Search results

No, the TL1754 bucket makes this hard to do. It doesn't have a straight/one angle back but instead has the massive angle shift, 45 - 90 degrees. This will make it where you have to build out something to create a solid back to accept the attachment SSQA frame. It might just be easier to sell...

I don't know if I have "over used" my Titan forks but they have done exceptional with everything I have asked them to do.

I got everything installed and it is very nice. Two issues. 1) They are default black unless you call and tell them to paint it orange. I didn't know this and it isn't listed anywhere. I figured since they are custom made for a Kubota machine, and all the pictures have them as orange, it...

Finally pulled the trigger, I thought I could live without it but I don't want to sell my grapple bucket or forks, so I might as well put it to use. $950 delivered, I will post pics when it comes in. I figure I will have the L35 for a long time. It is a beast of a machine. Might start...

I have decided on the ATI QA though I haven't pulled the trigger yet. W. R. Long is $875 out the door with a 4+ week lead time, plus having to drive to pick it up so $890 or so. The ATI is $915 delivered to the house in about a week. Plus, the ATI is orange, is the original model, and has been...

About the same. Unfortunately, I already have a 3rd function valve, grapple bucket, and forklift attachment so I need to make something happen.

After talking to a Kubota dealer, they had no idea how to get a quick attach for a TL720 loader. It looks like ATI and WR Long are the best bets, the WR Long retails for $745. As far as the WR Long 3rd function, I am good just swapping it all over from the other tractor. I will have to modify...

Thanks! I will check it out as well.

Cool, if we don't get much here I will try to remember to let you know what I end up doing.

Thanks for the response. In case it wasn't clear, I was wondering if anyone else had purchased one of the brands I mentioned and were happy with it or had any recommendations.

After a few month hiatus I am back in the Kubota family. I will be selling my Mahindra, not through any fault of its own, I just found an L35 at a good price and no reason to keep both tractors around. Anyway, I am looking for options to convert the pin-on bucket to SSQA. I have seen several...

HST pipe on right side? If you are sitting on the tractor and look down, it should be HST pipe on left side and everything else on right side. Filters in both.

My idea is different and depending on how much movement I want, it is adjustable. There is room for about a 2 inch wide u-bolt that can be anywhere from 2 - 4 inches in length. It would attach where the seat has the bumpers and rests on the frame when it bottoms out. There is a perfect...

I must not have been clear, I bet it is coming from the lever and that is where the washers go. As you pointed out, the leak will run down and that is likely since it is on a pressure line. A leak from a suction line will be a slow drip, a pressure line will either be a more forceful drip or a...

By suction, I mean from the sump to the pump.

Bill, On the HST the system is all one. On the left hand side near the bottom of the case is the suction and filter for the HST, on the right hand side is the suction and filter for the "hydraulic system." The part that you are talking about is the supply for the 3 pt system. There is a copper...

Thanks, that will be good. I will look at it tomorrow as well... I will have my 260 lb brother stand on it, that might get it into position.

Thanks for the response, I got it because I read quite a few favorable reviews of it and I didn't see anything about it being too high. Do you mean that you modified the base, or modified the seat by "clamping it down at the lowest level." I might be interested in doing the same thing if you...

For those that I have replaced their factory B7100 seat with the Tractor Supply suspension seat, how high does yours sit? I took the factory flip and rear spring bracket off to get it lower and have it on the the 3" or so factory bracket. To put it lower, I would have to build a spacer for the...

So, I have the diagrams that are linked below and my hydrualic system is identical to this with the exception of having the additional block face for a FEL and the FEL return line goes back to near the fill spot... I am trying to figure out what is pressure and what is return on the normal...