Search results

Fire to seat beads.....reminds me how stupid I was installing suicide rim locks without a cage in my early days. I think that old shop still has the license plates RTV patch on the roof(18 roof ceilings) that the lock ring made when it slipped out while trying to seal. Second on removing valve...

The jack handle always comes in handy as a cheater pipe(just make sure you can reinstall the handle as some are spring loaded). Also when trying to air the tire up, is the tire off the ground, and does it appear the bead of the tire is on the rim(both sides). And remember six point sockets are...

The 2 bucket sizes for the LX2610 is a 54 inch bucket and a light duty 60 inch bucket. I thought I ordered the 60 inch bucket when I ordered the tractor but am very happy with the abusive that the 54 inch bucket has endured(not sure the light duty bucket would have endured the abuse). With a...

Second on the Lucas grease. Although I also don't use a hand pump(Milwaukee M18). Always wondered if Lucas grease is the same company that made electrical(Lucas the prince of darkness) parts for MG?

Have no experience with Kubota coolant drain plugs, but the VW's, John Deere's, Chevrolet's, GMC's, and Nissan's diesel engine plugs have been F*!king tight. I would not use an impact wrench on it. I would try a rust penetrate( I use Kriol) over a few days and a longer cheater pipe. Also wear...

I have 2 inch spacers on my LX2610HSDC(cab version) and use a 60 inch MMM. Also have the backhoe and the tires are the R14T's(smaller of the two sizes available). Also have the WSM manual for it, its a pdf file if want that PM me with an email and I'll give you the goggle docs location.

It is possible as the heat in the starter maybe causing a connection issue, but, before I replace the starter I would wire a 12 volt(194 bulb) bulb to the small post(at starter) and ground(battery negative). When it wont start verify the bulb is bright. If bright-starter, if not...

I have the R14T on my LX2610 and have yet(not for lack of trying)got it stuck. I went with the smaller size as I have a mid mount mower and it is used on hills, so, the smaller tire helps with the center of gravity being lower. I take the tractor in snow, mud, sand, lawn, and gravel.

Shut it off, as the DPF needs to be hot to operate properly. I have researched this issue a lot before buying my LX2610 as I wanted a little more horsepower, but this will be my last tractor(maybe) and did not want this emission issues down the road. Researched this and even my brother bought a...

If I remember correctly on my BX2370 it had a bracket that rotated down and attached to the rear mower attachment point(silver pin with the spring on it). Also what kind of pin is/was installed their? IIRC my had a circular key type ring. Not to be condescending have you read all the manuals...

Pictures would be very helpful as there are several pins. Are you talking the pins at the front? Also I believe you are suppose to lock the lift up when to MMM not installed(or do not want movement).

I agree with Wolfman completely normal. On a side note, had a turbocharger Malibu with a catalytic convertor failure (plugged) cold engine start within 3 minutes of running turbo and exhaust manifold glowing red hot(no night needed) and would only rev to about 1500 RPM's(tried this a couple...

I would follow the wires from switch to starter. Unplug and inspect any connectors as it sounds like high resistance on the starter circuit. By jumping at starter(big post to small post right?) proves battery good and grounds are also good.

Pictures didn't copy but 2 wire switch, just wire your switch in parallel. Do this at your own risk. This information is for knowledge only and not to used to bypass any or all safety systems. In simple terms if you perform this and then get hurt/killed, DO NOT SUE ME or anyone else as you...

Cab or rops?

sold

Reminds me of the saying "Nothing is more permanent than a temporary fix."

If I remember correctly I had my instrument cluster replaced for no charge by Kubota. I was 3 months out of warranty, but its a known issue, therefore the dealership was able to get Kubota to goodwill the repairs. Kubota had to realized they made a major mistake by not making an instrument...

Does anyone know if all K connect attachments are interchangeable? As in the snow plow(snow blower or a brush) for a BX fitting onto a LX or RTV? Also can you buy just attachment side bracket assembly separately?