Recent content by Squawker Ranch

  1. S

    L285 Model 700 Loader control valve failed

    Reporting back. I ended up purchasing a 2 Spool 8 GPM Prince MB21GB5C1 DA Valve w/Float from Surplus Center. Easy install- had to drill the factory mount plate on the loader, but that took all of 30 seconds. Once installed, on the first tug of the controls, one of the metal lines sprung a leak...
  2. S

    L285 Model 700 Loader control valve failed

    More from the manual. You can’t find this online. Maybe for sale on eBay …
  3. S

    L285 Model 700 Loader control valve failed

    I’m happy with two control arms-I’ve gotten used to them, so I’m considering the following: https://www.surpluscenter.com/Hydraulics/Hydraulic-Valves/Directional-Control-Valves/2-Spool-10-GPM-Chief-220907-DA-Hydraulic-Valve-9-12461.axd The question I have now is which adapters do I need to add...
  4. S

    L285 Model 700 Loader control valve failed

    Sorry, didn’t answer fully. The operator’s manual states that it is a Kubota Model 700 Loader. There is no reference for it online, nor does Kubota have anything digitized in their parts system as a “local option”. If I have time later, I’ll scan the manual
  5. S

    L285 Model 700 Loader control valve failed

    There are two hoses coming off of the pump going to the valve, then four hoses connecting to the loader. The pump is part of the 3pt mechanism and sits directly under the seat. Without the loader option, there is no loader control valve, but there is a 3pt and 3pt controller.
  6. S

    L285 Model 700 Loader control valve failed

    Thanks Dave. I was aware of the aftermarket option but not the specs. I had no idea regarding the flow rate, so that was a big help. The L285 doesn’t have power steering, so no need for power beyond. I’m trying to avoid getting a PhD for the L285 as I intend to move on from it sooner than...
  7. S

    Hydraulic Control Assembly for Kubota Model 700 Loader, Kubota L285, L225 or L175 Tractor

    The 700 loader was compatible with the L285 L225 and L175 Tractor. I'm looking for the hydraulic controls as the shaft on the #1 valve has given its all and there are no new replacement parts.
  8. S

    L285 Model 700 Loader control valve failed

    Hi, My L285 has a Model 700 Loader. Control Valve #1, which lifts/lowers the arm, is sticking, and the shaft appears to have scoring and may be bent. I had it rebuilt recently, but the repair shop said he could only replace the o-rings, that the shaft would be near impossible to find. The...
  9. S

    tires for L285

    I assume there is more freedom of outside diameter with 2WD vs 4wd, within limits of course. But an inch difference in diameter isn't going to kill a center differential w 2wd. I could go John Force if I wanted. It might looks silly, but it would roll ;-)
  10. S

    tires for L285

    2WD L285
  11. S

    tires for L285

    Hi, I have a L285 and am looking to replace the existing tires with something that provides better performance in sand. Our arena is small, and the front tires tend to plow when making tight turns and the rear tires could have more float, less tread. Suggestions?
  12. S

    Aftermarket hydraulic cylinders vs OEM for L285

    Ok, sounds like best next step is determine if its repairable. I figure it needs a rebuild at minimum, but am concerned about the amount of pitting. Next challenge is to find a local shop
  13. S

    Aftermarket hydraulic cylinders vs OEM for L285

    I should have included that the loader is a model 700
  14. S

    Aftermarket hydraulic cylinders vs OEM for L285

    My L285 needs new hydraulic cylinders due to pitting of the piston shaft. This tractor spend a lot of time outside in the elements. Are there aftermarket options? If so, who is a good source? Thanks Tim Squawker Ranch Topanga CA