Oil Filter cross reference

Pepsiboy

Pepsiboy

Member

Equipment
BX2350D, FEL, MMM, Rear tiller
Oct 3, 2014
170
3
18
Shell Knob, Mo
Does any one know what the Fram or Wix filter numbers would be to fit my BX2350? Kubota numbers are HH150-32430 for the engine filter and HHK20-36990 for the Hydraulic filter. I have tried, but am unable to locate aftermarket filters to fit. These filters from Kubota Dealer have gone up to $16 for the engine filter and $19 for the hydraulic filter. On my VERY fixed income, this is hard to justify. I have located the fuel filters and the air filter aftermarket for $3 for fuel and $6 for air.

Thanks, in advance.

Dave
 
D

Diydave

New member

Equipment
L2202 tractor, L185f tractor
Oct 31, 2013
1,635
11
0
Gambrills, MD USA
Pepsiboy said:
Does any one know what the Fram or Wix filter numbers would be to fit my BX2350? Kubota numbers are HH150-32430 for the engine filter and HHK20-36990 for the Hydraulic filter. I have tried, but am unable to locate aftermarket filters to fit. These filters from Kubota Dealer have gone up to $16 for the engine filter and $19 for the hydraulic filter. On my VERY fixed income, this is hard to justify. I have located the fuel filters and the air filter aftermarket for $3 for fuel and $6 for air.

Thanks, in advance.

Dave
Click to expand...
Take your number, and tractor info to a good quality auto parts store. Most of the time they can cross it for you...:D:D
 
C

C15TA

New member

Equipment
170 Allis Chalmers , 580E Case & BX25D
Oct 1, 2015
16
0
1
Castleton ON
Dave, I got the oil filter HH150-32430 to cross to a WIX 51365 or a Fram 6607.
I stock that Fram number in my shop and I pay 2-3 bucks CDN. for them. WIX says there is no direct replacement at this time for the hydraulic filter and nothing will come up under Fram. Hope this helps.
Barry

Product Specifications
Part Number: 51365
UPC Number: 765809513655
Style: Spin-On Lube Filter
Service: Lube
Type: Full Flow
Media: Enhanced Cellulose
Height: 2.58 (66)*
Outer Diameter Top: 2.69 (68)*
Outer Diameter Bottom: Closed:
Thread Size: 20X1.5 MM
By-Pass Valve Setting-PSI: 8-11
Anti-Drain Back Valve: Yes
Beta Ratio: 2/20=6/20
Burst Pressure-PSI: 300
Max Flow Rate: 9-11 GPM
Nominal Micron Rating: 21
( )* denotes metric
Gasket Diameters
Number O.D. I.D. Thk.
Attached 2.475 (63)* 2.173 (55)* 0.233 (6)*
 
Last edited:
FTG-05

FTG-05

Active member

Equipment
L4330 w/FEL, RTV-XG850 and ZD326S
Jul 21, 2013
282
115
43
TN
HH150-32430 = Wix 51365XP or 51365; Fram PH6607 or PH6017A

HHK20-36990 = This is a valid competitive part number and there is no replacement at this time. Had no luck with Fram or Baldwin as well.
 
D

Diydave

New member

Equipment
L2202 tractor, L185f tractor
Oct 31, 2013
1,635
11
0
Gambrills, MD USA
Daren Todd said:
This is just an FYI for other folks looking. You can go to either of these websites and type in your filter number and they will provide you with there part number ;)

http://www.wixfilters.com

http://www.framcatalog.com/application.aspx?b=F
Click to expand...
CT15A, welcome to the forum... Darren, your links should go on the links sticky, if they aren't already there...

Re Hydraulic filters, I have a L2202, Shaffer's equipment can get the filter, but I took mine into a TSC, one snowy day, I had made a stub shaft, that fit the metric threads on the original filter, also had the measurement for the inner and outer seal surfaces, and sat there, pulling filters out of the boxes, and comparing the filters out, comparing the shaft and seal surface measurements, came up with a fram#3593A. While it is smaller than the OEM filter, but everything worked fine, after its installation, and its $7, rather than $50+ that the one from Shaffer...:D:D
 
Daren Todd

Daren Todd

Well-known member
Lifetime Member

Equipment
Massey Ferguson 1825E, Kubota Z121S, Box blade, Rotary Cutter
May 18, 2014
10,159
6,596
113
Vilonia, Arkansas
Diydave said:
CT15A, welcome to the forum... Darren, your links should go on the links sticky, if they aren't already there...

Re Hydraulic filters, I have a L2202, Shaffer's equipment can get the filter, but I took mine into a TSC, one snowy day, I had made a stub shaft, that fit the metric threads on the original filter, also had the measurement for the inner and outer seal surfaces, and sat there, pulling filters out of the boxes, and comparing the filters out, comparing the shaft and seal surface measurements, came up with a fram#3593A. While it is smaller than the OEM filter, but everything worked fine, after its installation, and its $7, rather than $50+ that the one from Shaffer...:D:D
Click to expand...
They are up there, at least the Baldwin and wix sites are :D
 
T

ThisIsNotaStep

New member

Equipment
2005 bx23 tlb
Nov 26, 2010
133
2
0
Ontario, Canada
Pepsi .. I have the same BX, the engine oil filter is available almost everywhere, Walmart, C/T, TSC .. it is a PH3593A. I have not been able to find a hydro filter in any chart, or from any supply store. What brand/part no is the air filter you came up with?
PCDietCola boy.
 
  • Like
Reactions: 1 user
Pepsiboy

Pepsiboy

Member

Equipment
BX2350D, FEL, MMM, Rear tiller
Oct 3, 2014
170
3
18
Shell Knob, Mo
Diydave said:
Take your number, and tractor info to a good quality auto parts store. Most of the time they can cross it for you...:D:D
Click to expand...
Diydave,

I have tried that at 4 different parts stores (NAPA, Bumper to Bumper, O'Reilly's, and Allied), they ALL said the same thing. No cross available for EITHER filter.

Dave
 
Pepsiboy

Pepsiboy

Member

Equipment
BX2350D, FEL, MMM, Rear tiller
Oct 3, 2014
170
3
18
Shell Knob, Mo
ThisIsNotaStep said:
Pepsi .. I have the same BX, the engine oil filter is available almost everywhere, Walmart, C/T, TSC .. it is a PH3593A. I have not been able to find a hydro filter in any chart, or from any supply store. What brand/part no is the air filter you came up with?
PCDietCola boy.
Click to expand...
ThisIsNotaStep,

Thanks for the reference number. I'll check that out next time I go to Wal-Mart. The fuel filter I am using is from Wal-Mart. I don't remember the number, but it is the same size and has the same size nipples to attach the fuel lines. It is a 5 micron filter for about $2.50 US. The air filter is a Fleet guard AF 25550 from NAPA for about $7.00 US.

Dave
 
D

Diydave

New member

Equipment
L2202 tractor, L185f tractor
Oct 31, 2013
1,635
11
0
Gambrills, MD USA
Pepsiboy said:
Diydave,

I have tried that at 4 different parts stores (NAPA, Bumper to Bumper, O'Reilly's, and Allied), they ALL said the same thing. No cross available for EITHER filter.

Dave
Click to expand...
Bumper to bumper has been able to get the filters I need on the old ones I have. Maybe yours is too new...:D:D
 
M

mattwithcats

Active member
Jun 17, 2017
777
66
28
Virginia
You must log in or register to reply here.

Top Bottom