BX2370 wheel spacers

Bxrider · May 25, 2017

Hello all I'm new to your forum family.
I've been looking at it for a while but joined
today. I've been looking at wheel spacers for my BX for
A while. Found these on eBay just wanted to share
Put them on today fit is perfect

jmf78 · May 25, 2017

Nice buy. Hope they work out for ya. I just put on some two inch Brotek spacers. Nice improvement all around for sure!
And welcome to OTT!

maclean · May 27, 2017

I have three Brotek inches and I love them...

MadMax31 · May 29, 2017

Thanks for the info. Just ordered a pair!

Manvito · Jun 5, 2017

Bxrider said:
Hello all I'm new to your forum family.
I've been looking at it for a while but joined
today. I've been looking at wheel spacers for my BX for
A while. Found these on eBay just wanted to share
Put them on today fit is perfect

I don't mean to hijack you post but how did you find out those fit your tractor? I have a B2601 and I really like the price of those spacers. I'd love to hear what you think about the quality of those spacers as well.

BotaLoda · Jun 23, 2017

For reasons I won't get into, I got a 54" deck. I see they have 1.25" spacers. Are they going to help or a waste of money. (although at that price I think it's a risk I'll take). My dealer also had the tires filled, I'm guessing while laying flat or maybe at a slight angle. They were TOO full. Not enough air in them for the tires to compress on bumps. With the valve stems at the top I let out the extra liquid and filled with air. I have a good amount of rear ballast. Would it get more stable if I let the liquid out to about half way/axle level?

Bxrider · Jun 24, 2017

To make sure they would fit my BX I looked for spacers with their specs listed.
Bolt pattern and wheel center size were what I went with.
As far as quality fit was perfect, spacer material and hardware were the same
as those listed for a BX.

tiredguy · Jun 25, 2017

Absolutely amazing to find spacers for a Jeep that the bolt pattern matched
to fit your Kubota and a cheaper than dirt price to boot. If they do in fact fit
and work out as planned sharing the information and source is awesome and
what the forum is all about.
Kudos!
Al

Orangeglow · Jun 25, 2017

I tried to find those spacers that the OP listed, but I cann,t find them.

By any chance, can you post a link to those from e-bay ?

Bjones · Jun 26, 2017

I too am looking to install spacers for the stability factor. Will the spacers case any structural damage or cause any damage in any way. I have a L2800 and use my tractor on hilly areas and the extra wide footprint would be helpful. Thought about 2". Who has the best price and quality spacers? Thanks guys

MadMax31 · Jun 26, 2017

Ive had them on for 10 hours now. No issues.

Bxrider · Jun 27, 2017

tiredguy said:
Absolutely amazing to find spacers for a Jeep that the bolt pattern matched
to fit your Kubota and a cheaper than dirt price to boot. If they do in fact fit
and work out as planned sharing the information and source is awesome and
what the forum is all about.
Kudos!
Al

They have been on my BX2370 since the end of May.
They do make it a lot more stable.

Bxrider · Jun 27, 2017

Orangeglow said:
I tried to find those spacers that the OP listed, but I cann,t find them.

By any chance, can you post a link to those from e-bay ?

I don't have the link, search 5x4.5 wheel spacers then make sure they will work with the center hole of your wheel. Hole size should be listed in their specs. I know the ones listed for jeeps work, I think maybe the ones listed for Ford might.

D2Cat · Jun 28, 2017

MadMax31 said:
Ive had them on for 10 hours now. No issues.

Max, you sure they haven't begun rusting?

gulfmp · Jun 28, 2017

Can these spacers be used with the 54" mmm?

SLIMSHADIE · Jun 28, 2017

I have Bro-Tek's, very nice. There web site says upto 1.5" for a 54" mmm.

http://www.bro-tek.com/wheel_spacers/

MadMax31 · Jul 1, 2017

gulfmp said:
Can these spacers be used with the 54" mmm?

No, 1.5" max with 54" mmm.

My 2" push tires close enough I can't remove pin and spin bogey wheel 90° to make deck slide out effortlessly. Now Im dragging the two rear wheels. Oh well.

Orangeglow · Jul 1, 2017

Bxrider said:
I don't have the link, search 5x4.5 wheel spacers then make sure they will work with the center hole of your wheel. Hole size should be listed in their specs. I know the ones listed for jeeps work, I think maybe the ones listed for Ford might.

Thanks for the info.

I found the 2 inch spacers on e-bay, but they are out of stock for a couple more weeks.

I ordered the 1.5 inch ones and will also get a set of 2 inch ones when they are back in stock.

howie70 · Jun 6, 2018

I have scoured ebay looking for 1.5" spacers to fit my BX2370. My center hole is 3.125" or 79.375mm. I can't find anything close.
Any of you guys mind posting a link to what you found?

Orangeglow · Jun 6, 2018

Try this one, they are even cheaper now than when I bought mine.

https://www.ebay.com/itm/1-5-inch-5...KK-ZJ-MJ-TJ-/380972451618?hash=item58b3ba4722

BX2370 wheel spacers

New member

Attachments

Member

New member

Member

New member

Member

New member

New member

Active member

Member

Member

New member

New member

Well-known member

New member

Member

Member

Active member

New member

Active member