Search results

Hello, I have a 2005 BX 23D with the LA 210 loader on it, I am looking to covert to a quick attach system but having trouble locating someone that offers one. Looks like Everything Attachments offered them at one time but currently not available. Looking to get a set of forks and covert my...

Thanks I kind of like that even better.

Thanks for the information, I can now keep an eye for a used blower or plow.

Hello, what model snow plow and snow blower with front hitch will fit my 2005 BX 23D? What is a fair price for a used plow and or blower? Thanks

Thank you everyone for the suggestions, I will keep everyone post once I have a chance to review the area of concern. I did go ahead and pressure washed the area and will most likely try the dye and the baby power as well to see if I can pinpoint the leak. Once I see where it’s coming from and...

Hello, I have a hydraulic leak near the control valve, I cannot pinpoint the exact location of this leak. I have heard of dyes being used and was looking for advice from others on how they found difficult leaks. The machine is a BX 23D. Any suggestions would be appreciate. Thanks

Dave, You were right on, the light bulb went off, part #130 the screw has a slot on the top for a screwdriver, you put the sending unit in and turn the screw to lock under the tank lid then snug up the bolts. Problem solved. God is good! Tony

Dave, I inherited the machine from my father in law whom passed away and noticed the fuel gauge was not registering so I tried to order the complete rebuild kit which is NLA, so I bought every last piece individually from Messicks. It appears the rubber gasket sits down into the tank slight...

It is leaking between the rubber gasket #30 and the tank itself. Brand new rubber gasket. Am I correct that this assembly just sits onto the tank with nothing keeping pressure on it to seal? I know it must be turned perfectly to sit down in the opening flush. I am not sure what I am doing wrong...

I have rebuild the entire fuel sending unit with all new parts, gaskets etc. Had to buy each nut, bolt, gasket separately as the kit is no longer available. Problem is I have a constant leak between the sending unit and the tank itself. It appears the entire sending unit carefully fits into the...

Sorry for the delay in getting back to everyone, I believe I have found the culprit, the neutral safety switch was not fully depressing therefore not allowing the engine to crank. I removed the switch and bracket and clean up everything ,cleaned both screws and moved the switch all the way...

I have a 2005 Kubota BX 23D that will not crank some times, it’s an intermittent issue. I have replaced all three safety switch’s, new battery and new starter. Is there something else I should check, maybe a relay? I am stumped right now. Used it all day today no issues mowing, turned it off to...

Good moruing, I am looking for any advice to install a new O-ring on the side of the transmission case. My question is, do you have to remove the transmission case to install the new O- ring or can you replace the O-ring with the transmission case in the tractor? Also the plug (K2561-11140) has...

Thanks for the sunex tool set suggestion, I ordered it today and should be here tomorrow. I appreciate your advice and have ordered a new seal, this tool is exactly what I needed and didn’t even know such a toon existed. I am hoping to be successful this try!

Thanks, this Seal can only be accessed from one side unless you split the hydro unit which I would rather not do, I am going to buy another seal and if is starts to roll then I will take your advice and use a very thin feeler gauge to try and peel it back up. Just hate to pay someone $129 to put...

Hello, I have a 2005 BX 23D that I just replaced the front PTO shaft and have completed the reinstall of the Transaxle to the main frame of the tractor, tested everything and the PTO works fine. However I noticed a leak coming from between the Hydrostatic unit and front cover plate, so I...

Ok so I wanted to give an update on the mid PTO not working, I decided to remove the transmission and rear assembly from the tractor which was successful. After a thorough cleaning, I removed the front cover plate and discovered the rear PTO shaft had broken in two about three inches from the...

I heard back from my local kubota dealer with regards to the repair cost. They are saying 8-10 hrs to split tractor and another 8-10hrs to reassemble, then a few hrs to fix problem at $129.00 hr plus a 10% shop supply fee, I have read the repair manual and be,I’ve I can split the tractor and...

Understood and thank you for the information, I am assuming the 8 hrs is just for the removal or is the 8 hrs to complete the job, just curious. Thanks again, valuable information you have provided for sure.

Can the cover be removed with the trans unit in place or do you have to remove the trans unit from the tractor? If I can remove the cover and get to everything, then I will probably go ahead and do the job. If the trans has to be totally removed from the tractor I will see what the cost is from...