Search results

A follow up on this. I received new cover from Kahuna on Saturday after I had to make a scene at post office (god they are awful). Installed cover today. Much heavier then old one, perfect machining and fit. Left relief valve way out. Fired up tractor, no leaks and hydraulics all work...

Yes it was clearly a relief valve malfunction. No luck on pump cover, no good machine shops here either. Looks like I am buying a new pump.

Not a bearing support, it has a areas machined out. See pic.

Can you get parts for hydraulic pumps? Pump #35110-76100 was being used on tractor. Went to scoop a load of topsoil and the back cover plate of pump cracked. Innards of pump and main case seem fine. Can I get a new back plate?

Hooked lines together, fired up and 3pt lifted me and my brother right up and just off idle, before it wouldn't even lift me. So it would seem the pump is fine. Looking like something in valve even though it doesn't make sense to me how it could be losing pressure in the valve body without...

Got a fitting today so that I can tie the two lines going up to the loader together and bypass the loader valve. I also got an adapter so I can check pressure on the line. I don't see a pressure test port on the pump or lines. Have not tested anything yet. I have changed screen filter by...

Still no progress on this. Tractor has run at idle for long periods of time, with levers moved and without. Still not building pressure. Three point hitch will not lift me! I guess tomorrow I will get a coupler and tie the two hoses together bypassing the loader valve and see if I get three...

OK After having sat for about 4 hours I just had it running for about 30 minutes. Still not making pressure. I can see that fluid is moving through transmission from looking at fill port. Fluid does look a little milky (maybe foamy?) compared to new that I added. I let it run at idle and...

Let me rephrase. A very old line (hose) cracked and sprayed fluid all over. A time it broke loader and 3 pt were working fine. Pressure and return from loader go to a block on top of transmission where pressure line come from pump.

I have an 1982 L245DT with a Kubota front loader plumbed into hydraulic system. While operating loader last week I blew return hose from loader valve. Immediately shut down tractor. Got a new hose and checked fluid almost no lost. Tractor sat for a couple days before new hose attached today...

I ordered a new shift fork and new pins and springs. Very affordable. I have not gotten into it yet. Working on a mower in the shop and then I will pull it in. I know I can remove the shift handle plate and then it looks like there is a plate that holds all the shift forks bolted to the top...

Hi Vic. Can you take a look at my L245DT transmission post? I am in need of replacing the reverse shift fork and need to know what the process is.

I have a problem with my L245DT. When I select reverse it does go in but the fork where the shifter pivots is so worn that when the selector pivots towards front of tractor for reverse, it is able to move left and fall out of the fork and end up sitting above the center fork. We have to undo...

I was thinking of hooking the pressure and suction to the pump on my 28ton gas powered log splitter to see if it would dig under that power.

We have just set it up and been playing around with it. It will dig about 2" at a time. Won't curl the bucket in with a load. The stabilizers will lift the machine but I would think the boom and curl cylinders should either dig or pull the machine. We tool the filter off it was a bit dirty...

We have identified the pieces missing. Cannot purchase anymore but Woods who purchased Grizzly is sending us some specs on having them made. I will take a picture of the setup soon. In the meantime, it has no power. All the cylinders move, but once it hits the ground has little digging...

I have an L245dt with a 3 point attached backhoe run by a pto driven pump. I know its not the best setup (subframe would be better) but mainly using it to plant remove shrubs and move rocks around walls. Anyway, I got it all attached and the problem I am having is that when it is at a good...

I have a 1980 L245DT that came with a loader installed. I am not sure of the model but it is from 1980. One of the bucket curl cylinders has a bent rod. Can I get a new rod and rebuild kit? Or should I get a complete new cylinder? Part numbers would be helpful. I will take a picture of the...

What is the recommended battery (group / CCAs) for a L245DT? I will be wanted to start tractor occassionally over the winter.

I had the front left wheel get real wobbly on the new to me tractor today. Took the wheel off and I could tell it was some bad bearings. I am using generic terms here. I took the outer bearing case off by loosening 6 bolts with it came the large drive gear for the 4 wheel drive. The inner...